| “This site contains affiliate links for which OEMDTC may be compensated” |
April 25, 2019 NHTSA CAMPAIGN NUMBER: 19V326000
Incorrectly Wired Seat Belt Harness Connector
In the event of a crash necessitating air bag deployment, an incorrect classification may result in the passenger frontal air bag deploying even if there is a child in the front passenger seat, increasing their risk of injury.
NHTSA Campaign Number: 19V326
Manufacturer Jaguar Land Rover North America, LLC
Components ELECTRICAL SYSTEM, SEAT BELTS, AIR BAGS
Potential Number of Units Affected 7,060
Summary
Jaguar Land Rover North America, LLC (Jaguar Land Rover) is recalling certain 2014-2015 Jaguar F-TYPE vehicles previously remedied under Recall 14V-714. The seatbelt harness connector which connects the Seatbelt Tension Sensor (STS) to the Occupant Classification Sensor Control Module (OCSCM) may not have been correctly wired. As a result, the Restraint Control Module (RCM) may not accurately detect if an adult or child is occupying the seat.
Remedy
Jaguar will notify owners, and dealers will inspect the seat belt assembly and repair the seatbelt tension sensor harness as necessary, free of charge. The recall began June 3, 2019. Owners may contact Jaguar customer service at 1-800-452-4827. Jaguar’s number for this recall is H208.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
Check if your Jaguar has a Recall
SAFETY RECALL H208 (NHTSA 19V-326)
| NAS19.05.012 | WORKSHOP | USA | AFTERSALES BULLETIN MAY 16 , 2019 |
Jaguar Land Rover North America, LLC has informed the National Highway Traffic Safety Administration (NHTSA) of its intent to perform a voluntary Safety Recall on certain 2014-2015 model year Jaguar F-TYPE vehicles imported into the United States market. Information relating to this Recall will be posted on the National Highway Traffic Safety Administration website.
United States Federal regulations require that retailers must be notified within a reasonable time after the manufacturer decides that a defect that relates to motor vehicle safety or a noncompliance exists.
United States Federal law requires retailers to complete any outstanding safety Recall service before a new vehicle is delivered to the buyer or lessee. Violation of this requirement by a retailer could result in a civil penalty of up to $21,780.00 per vehicle.
This Recall Service Bulletin serves as notification to all Jaguar retailers in the United States and Federalized Territories that any affected new vehicles may not be sold and delivered for customer use until the Recall repair is completed.
DESCRIPTION OF ISSUE
An issue has been identified on certain Jaguar vehicles within the listed Affected Vehicle Range where the affected vehicle’s seatbelt harness connector which connects the Seatbelt Tension Sensor (STS) to the Occupant Classification Sensor Control Module (OCSCM) may not have been correctly wired. The OCSCM senses whether there is an occupant in the front passenger seating position, and the STS senses whether tension on the seatbelt indicates a child restraint is being used in the front passenger seating position. Both sensors provide information to the restraint control module (RCM) which informs whether the front passenger airbag should be activated, depending on whether the sensors detect the seat is occupied and/or that it is occupied by an adult passenger.
AFFECTED VEHICLE RANGE
F-TYPE (X152)
Model Year: ………………. 2014-2015
VIN: …………………………….. SAJWA6FC6E8K00001-SAJWA6ET4F8K19746
A total of 7,060 vehicles are potentially affected in the USA and Federalized Territories. Visit the British Brands Sales Suite (BBSS) website for a list of affected vehicles at your retailer.
EFFECT ON VEHICLE OPERATION
Should the STS not have been wired correctly, the front passenger airbag may not be suppressed, and may remain activated, even when a child restraint is placed in the front passenger seat or a small statured adult occupies that seat. In the event of a crash necessitating deployment of the front passenger airbag, a child or small stature occupant may be at an increased risk of injury.
SERVICE PROGRAM / REWORK ACTION
Owners will be notified and instructed to take their vehicle to an authorized Jaguar retailer who will inspect the seat belt assembly. If required, the technician will complete a repair to the seatbelt tension sensor harness.
There will be no charge to owners for this action under this program.
OWNER NOTIFICATION
Owners will receive a notification by mail on or before June 21, 2019.
ACTION TO BE TAKEN
Use the Jaguar Land Rover claims submission system to make sure that the vehicle is affected by
this Program prior to undertaking any rework action.
Retailers are required to HOLD affected new vehicles that are within your control and refrain from
releasing the vehicles for new vehicles ale pending completion of the rework action. Affected
vehicles already in the hands of customers should be updated at the next available opportunity
once the Technical repair bulletin has been published.
Jaguar Land Rover North America recommends that affected sales demonstrator and loaner
vehicles are repaired before use and that used vehicles are repaired before sale. Retailers who
choose to proceed against this recommendation, where legally permitted, must clearly and
conspicuously disclose the open recall to the applicable customers.
Refer to Technical Bulletin H208NAS1, SAFETY RECALL: Seatbelt Tension Sensor Connector Wiring, for
detailed repair instructions.
PARTS
No parts required.
TOOLS
Refer to the Technical Bulletin referenced above for any required special tools
NOTE: use the Jaguar Land Rover claims submission system to make sure that a vehicle is affected by this program prior to undertaking any rework action.
At the time of confirming a booking for vehicle repair, make sure that all outstanding Recall and Service Actions are identified to ensure the correct parts are available and adequate workshop time is allocated for repairs to be completed in one visit.
Warranty claims must be submitted quoting the Program Code together with the relevant Option Code.
The SRO and parts information listed have been included for information only. The Option Code(s)
that allows for the drive in/drive out allowance may only be claimed if the vehicle is brought into
the workshop for this action alone to be undertaken.
Repair procedures are under constant review and therefore times/ prices are subject to change;
those quoted here must be taken as guidance only. Refer to TOPIX to obtain the latest repair
time.
Warranty claims must be submitted for payment within 30 calendar days of completion of the repair.
| PROGRAM CODE |
OPTION CODE |
DESCRIPTION | SRO | TIME (HOURS) |
PARTS / SUNDRY CODE |
QTY. / VALUE |
|---|---|---|---|---|---|---|
| H208 | A | Seatbelt tension sensor wiring – Inspect | 80.90.06 | 0.1 | – | – |
| H208 | B | Seatbelt tension sensor wiring – Inspect
Drive in/drive out |
80.90.06
10.10.10 |
0.1
0.2 |
–
– |
–
– |
| H208 | C | Seatbelt tension sensor wiring – Inspect and repair | 86.90.07 | 0.4 | – | – |
| H208 | D | Seatbelt tension sensor wiring – Inspect and repair Drive in/drive out | 86.90.07
10.10.10 |
0.4
0.2 |
–
– |
–
– |
Normal Warranty policies and procedures apply.
CUSTOMER RE-IMBURSEMENT FOR PREVIOUS REPAIRS
If a customer has indicated that they have already paid For t his concern as a normal retail repair (vehicle outside normal warrant y period), a copy of the repair invoice must be produced as proof of the repair. The retailer must directly reimburse t he customer and a claim For recovery of this cost should be made using the related damage procedure.
Supplementary claims for related damages can only be made once the Recall claim has been paid and accepted. Only repairs performed using approved Jaguar parts are eligible For reimbursement.
Submit claims quoting Program Code ‘H208’ and by clicking the ‘Related Damage’ radio button on the claim submission screen. Use Opt ion Code ‘X’ as detailed below and enter t he cost to be reimbursed against the sundry code of ‘ZZZ999’. All cost s are t o be entered in local currency.
| PROGRAM CODE |
OPTION CODE |
DESCRIPTION | TIME (HOURS) |
SUNDRY CODE | MISCELLANEOUSEXPENSE ($) |
|---|---|---|---|---|---|
| H208 | X | Re-imbursement to owner | N/A | ZZZ999 | Retailer Entered Value |
A copy of the invoice must be appended to the repair order for Warranty Audit purposes and Warranty Specialist review. Enter a brief comment in the ‘Technician Comments’ field on the claim to itemize and explain the charges.
Only vehicles eligible for this Safety Recall are included in t his process. Only one claim per vehicle for related damages will be accepted.
IMPORTANT SAFETY RECALL
This notice applies to your vehicle, SAJXXXXXXXXXXXXXX
June xx, 2019
Safety Recall H208: Seatbelt Tension Sensor Harness Connector Vehicles Affected: Jaguar F-TYPE
Model Year: 2014-2015
National Highway Traffic Safety Administration Recall Number: 19V-326 Dear Jaguar Owner:
This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act. Jaguar has decided that a defect relating to motor vehicle safety exists in certain 2014-2015 model year Jaguar F-Type vehicles.
Your vehicle is included in this Recall action.
What is the concern?
Jaguar Land Rover have identified certain F-TYPE 2014 and 2015 Model Year vehicles, previously remedied in recall J047, that may have had a seat belt service part installed containing the same defect as the parts from the original recall.
In the affected vehicles, the seatbelt harness connector which connects the Seatbelt Tension Sensor (STS) to the Occupant Classification Sensor Control Module (OCSCM) may not have been correctly wired. The OCSCM senses whether there is an occupant in the front passenger seating position, and the STS senses whether tension on the seatbelt indicates a child restraint is being used in the front passenger seating position. Both sensors provide information to the restraint control module (RCM) which informs whether the front passenger airbag should be activated, depending on whether the sensors detect the seat is occupied and/or that it is occupied by an adult passenger.
Should the STS not have been wired correctly, the front passenger air bag may not be suppressed, and may remain activated, even when a child restraint is placed in the front passenger seat or a small statured adult occupies that seat. In the event of a crash necessitating deployment of the front passenger air bag, a child or small stature occupant may be at an increased risk of injury.
What will Jaguar and your authorized Jaguar retailer do?
Jaguar is carrying out a recall of the vehicles mentioned above. An authorized Jaguar retailer will inspect the seat belt assembly. If required, the technician will complete a repair to the seatbelt tension sensor harness.
There will be no charge for this repair under this program.
What should you do?
Please contact your preferred authorized Jaguar retailer and provide them with your Vehicle Identification Number (VIN), and request a service date to complete the work required under Program code ‘H208’
Attention Leasing Agencies: If you are a vehicle lessor, Federal Regulations require you to forward this notice to your lessee within (10) TEN days.
How long will it take?
The work will be carried out as quickly and efficiently as possible in order to minimize inconvenience to customers and is expected to take up to 40 minutes, although your retailer may need your vehicle for a longer time. Your retailer can provide you with a better estimate of the overall time for the service visit.
Moved or no longer own this Jaguar vehicle?
If you are no longer the owner of this vehicle, Jaguar would appreciate the name and address of the new owner, using the return postage-paid card enclosed.
What should you do if you have further questions?
If you have any questions or concerns, please contact the Service Manager at your authorized Jaguar retailer for assistance. If you have any queries or concerns that your retailer cannot address, please contact the Jaguar Customer Relationship Centre at 1-800-4JAGUAR (1-800-452-4827).
You may also contact us by e-mail using the following address: jagweb1@jaguarlandrover.com. If you have the need to contact Jaguar by mail, please use the following address:
Jaguar Land Rover North America, LLC
ATTN: Customer Relationship Center
100 Jaguar Land Rover Way
Mahwah, NJ 07495
If after having attempted to take advantage of this recall you believe you have not been able to have your vehicle remedied without charge and within a reasonable amount of time, you may submit complaint to the:
Administrator, National Highway Traffic Safety Administration
1200 New Jersey Avenue, SE
Washington, D.C. 20590
Or call the toll-free Vehicle Safety Hotline at 888-327-4236 (TTY: 800-424-9153), or go to
Jaguar appreciates your confidence in our product and wish to do everything we can to retain that confidence. We recognize this service visit may be an inconvenience to you. Jaguar, in cooperation with your authorized Jaguar retailer, will strive to minimize any inconvenience to you caused by this program.
Rory Beattie
Vice President Customer Service Jaguar Land Rover North America, LLC
TECHNICAL Q & A: SAFETY RECALL H208
Main Message: An issue has been identified on certain Jaguar F-Type 2014 and 2015 Model Year vehicles, previously remedied in recall J0 4 7, that may have had a seatbelt service part installed containing the same condition as the parts from the original recall. Where installed, the vehicle will revert to its pre-J04 7 safety recall state.
Q1 Who do I contact if a member of the press contacts me about this recall?
A Please ensure Press enquiries are referred to the Jaguar Land Rover North America Press Office to the attention of:.
| Stuart Schorr Vice President, Communications & Public Affairs Jaguar Land Rover North America, LLC sschorr@jaguarlandrover.com Office +1-201-760-8561 Cell: +1-201-739-2964 |
Nathan Hoyt Product Communications Manager Jaguar Land Rover North America, LLC nhoyt@jaguarlandrover.com Off ice: +1-201-818-8316 Cell: +1-551-427-3199 |
Q2 Why is Jaguar Land Rover recalling certain Jaguar vehicles?
A These vehicles are being recalled due to an increased risk of injury to the vehicle occupants in the event of an accident where the Supplementary Restraints System (SRS) would deploy.
Q3 Can you tell me more about what is wrong with the vehicles?
A Affected Vehicle Range installed with Occupant Classification System (OCS), the seat belt assembly harness connect or which connects the seat belt tension sensor to the Occupant Classification System Control Module (OCSCM) may not be correctly wired. The wires are located in the incorrect terminals within the connector. The prior recall, J047, reversed this wiring in the seat belt side of the electrical connect or. In this condition the OCS will transmit a signal which does not indicate the installation of a child seat or the presence of a small person. In t his case of a child seat being installed, the OCS will not disable the passenger airbag, if a small person is present in t he passenger seat the passenger airbag deactivation indicator lamp will indicate that the seat is not occupied and the Supplementary Restraint System (SRS) will not deploy if required. The main purpose of the OCSCM is to provide the OCS with the occupancy status of the passenger seat. The Restraints Control Module (RCM) uses this information and the seat belt buckle status in the determination of the firing strategy for the passenger restraints. The main purpose of the seat belt tension sensor is to make sure t hat if a child seat is installed using the autolocking seat belt to restrain it in the passenger seat, the tension exerted on the seat belt tension sensor indicates t hat a child seat is installed. The RCM uses this information and the OCSCM status to determination the firing strategy for the passenger restraints. In both cases the OCS should determine if the front passenger seat is unoccupied, occupied by a child seat or small person, or occupied by an adult.
Q4 How would the customer become aware of potentially having this concern?
A The Occupant Sensor Control Module (OCSM) and Seatbelt Tension Sensor (STS) provides information to the Restraint Control Module (RCM) which informs whether the front passenger airbag should be activated, depending on whether the sensors detect the seat is occupied and/ or that it is occupied by an adult passenger.
Q5 Does this concern affect vehicle safety?
A Yes. Should t he STS not have been wire d correctly, t he front passenger airbag may not be suppressed and may remain activated, even when a child restraint is placed in the front passenger seat or a small statured adult occupies that seat posing an unreasonable risk to safety.
Q6 Has Jaguar Land Rover received many complaints?
A There have been no complaint s related to this issue of which Jaguar Land Rover is aw are .
Q7 Have there been any accidents or injuries?
A Jaguar Land Rover is not aware of any accidents or injuries which have been attributed to this issue.
Q8 How was the condition discovered?
A The JLR After Market Parts function identified a product difference related to certain F-Type vehicles and determined from service parts sales that a number of seat belt assemblies may have been installed to vehicles that were previously subject to recall campaign J047 without the correct seat belt harness connector reverse pinning modification as instructed in the J047 recall campaign being completed.
Q9 How long has Jaguar Land Rover known about this problem?
A The investigation into the issue began in February, 2019.
Q10 Is the defect leading you to any concerns regarding the reliability of a system, which is supposed to be designed and engineered for the passengers’ safety? What type of measures are you planning to take?
A We have no concerns with the overall reliability of the vehicle Jaguar Land Rover carefully monitors field data to make sure that any matters relating to safety and compliance are rigorously investigated.
Q11 What has Jaguar Land Rover done in production?
A Production vehicles are manufactured with correct wiring configuration.
Q12 What will retailer/authorized repairers do to the vehicles?
A An authorized Jaguar retailer will inspect t he seat belt assembly. If required, t he technician will complete a repair to the seatbelt tension sensor harness.
Q13 Which vehicles are affected by this recall?
A F-T YPE; SAJWA6FC6E8K00001 to SA JWA6ET4F8K19746
(Select ed vehicles within VIN range)
Q14 Are other Jaguar Land Rover models affected by these actions?
A No other models, other than those listed on this document, are known to be affected by this condition.
Q15 Are parts/software available to rework vehicles?
A No parts or software required for authorized Jaguar retailers to conduct this repair.
Q16 How much will the recall cost Jaguar Land Rover?
A Cost was not a factor in deciding to recall these vehicles.
Q17 How do I know if my Jaguar vehicle is affected?
A All owners of potentially affected vehicles w ill shortly receive a letter inviting them to contact an authorized Jaguar retailer for the work to be carried out.
Q18 How long does it take for the vehicle to be inspected and repaired?
A The work will be carried out as quickly and efficiently as possible in order to minimize inconvenience to customers and is expected to take no longer than 40 minutes. Due to retailer schedules, vehicles may be required for a longer time.
Q19 Can I continue to drive my Jaguar vehicle safely until it has been recalled?
A Customers are advised to contact an authorized Jaguar retailer if they have any concerns regarding their vehicles.
H208NAS1
TECHNICAL BULLETIN
16 MAY 2019
SECTION:
501-20A
SUBJECT/CONCERN:
SAFETY RECALL: Seatbelt Tension Sensor Connector Wiring
AFFECTED VEHICLE RANGE:
| MODEL: | MODEL YEAR: | VIN: | ASSEMBLY PLANT: |
| F-TYPE (X152) | 2014-2015 | K00001-K19747 | Castle Bromwich |
MARKETS:
NORTH AMERICA
CONDITION SUMMARY:
SITUATION:
An issue has been identified on certain Jaguar vehicles within the listed Affected Vehicle Range where the affected vehicle’s seatbelt harness connector which connects the Seatbelt Tension Sensor (STS) to the OCS (Occupant Classification Sensor Control Module) may not have been correctly wired. The OCS senses whether there is an occupant in the front passenger seating position, and the STS senses whether tension on the seatbelt indicates a child restraint is being used in the front passenger seating position. Both sensors provide information to the RCM (Restraints Control Module) which informs whether the front passenger airbag should be activated, depending on whether the sensors detect the seat is occupied and/or that it is occupied by an adult passenger.
Should the STS not have been wired correctly, the front passenger airbag may not be suppressed, and may remain activated, even when a child restraint is placed in the front passenger seat or a small statured adult occupies that seat. In the event of a crash necessitating deployment of the front passenger airbag, a child or small stature occupant may be at an increased risk of injury.
ACTION:
Retailers are required to HOLD affected new vehicles that are within your control and refrain from releasing the vehicles for new vehicle sale pending completion of the procedure(s) detailed in this Technical Bulletin. Unsold vehicles should have this performed as part of the Pre-Delivery Inspection (PDI) process but must have it completed prior to vehicle handover to the customer.
Affected vehicles already in the hands of customers should be updated at the next available opportunity.
PARTS:
No parts required.
SPECIAL TOOLS:
Refer to TOPIx Workshop Manual/Workshop Procedure for any required special tools.
WARRANTY:
| NOTE: |
Use the Jaguar Land Rover claims submission system to make sure that a vehicle is eligible for this program prior to undertaking any rework action.
At the time of confirming a booking for vehicle repair, make sure that all open Recall and Service Actions are identified to make sure the correct parts are available and adequate workshop time is allocated for repairs to be completed at one visit.
Warranty claims must be submitted quoting the Program Code and the relevant Option Code; this will result in payment of the stated time. The SRO and parts information is included for information only. The Option Code(s) that allows for the drive in/drive out allowance may only be claimed if the vehicle is brought back into the workshop for this action alone to be undertaken.
Repair procedures are under constant review and therefore times/prices are subject to change; those quoted here must be taken as guidance only. Use TOPIx to obtain the latest repair time.
Warranty claims must be submitted or payment within 30 calendar days of completion of the repair.
| PROGRAM CODE | OPTION CODE | DESCRIPTION | SRO | TIME (HOURS) |
| H208 | A | Seatbelt tension sensor wiring – Inspect | 86.90.06 | 0.1 |
| H208 | B | Seatbelt tension sensor wiring – Inspect
Drive in/drive out |
86.90.06
10.10.10 |
0.1
0.2 |
| H208 | C | Seatbelt tension sensor wiring – Inspect and repair | 86.90.07 | 0.4 |
| H208 | D | Seatbelt tension sensor wiring – Inspect and repair
Drive in/drive out |
86.90.07
10.10.10 |
0.4 0.2 |
Normal Warranty policies and procedures apply.
| NOTES: |
|
1
| WARNING: |
| Allow a period of 10 minutes to elapse after disconnecting the battery before undertaking any work on the Supplementary Restraint System (SRS). |
Disconnect the battery (see TOPIx Workshop Manual section 414-01: Battery, Mounting and Cables – General Procedures – Startup Battery Disconnect and Connect).
2
Remove the electrical connector cover for the passenger seatbelt tension sensor.
- Release the clips.
3
Release the electrical connector (C3R210) from the bracket.
4
At the seatbelt tension sensor side of connector C3R210, inspect that the electrical connector wires are positioned in the correct pin location as shown[✓].
- If the wires are in the correct position [✓], reverse steps 1-3 and release the vehicle.
- If the wires are not in the correct position [✕], continue to step 5.
5
Disconnect the electrical connector.
6
Use a suitable tool to remove the anti-backout device from the electrical connector.
7
Use special tool 418-595 to release the electrical connector.
8
Use special tool 418-595 to release the electrical connector.
9
Remove the white wire electrical pin from the electrical connector.
10
Remove the black wire electrical pin from the electrical connector.
11
Install the white wire electrical pin into the center cavity on the electrical connector.
12
Install the black wire electrical pin into the right side cavity on the electrical connector.
13
To install, reverse the 13 removal procedure.
2 Affected Products
Vehicle
| MAKE | MODEL | YEAR |
| JAGUAR | F-TYPE | 2014-2015 |
12 Associated Documents
Recall Acknowledgement
RCAK-19V326-5570.pdf 245.822KB
Loading...
Reload document 
Open in new tab
Defect Notice 573 Report
RCLRPT-19V326-7997.PDF 213.958KB
Loading...
Chronology
Loading...
Manufacturer Notices(to Dealers,etc) – AFTERSALES BULLETIN – SAFETY RECALL H208 (NHTSA 19V-326)
RCMN-19V326-2832.pdf 197.737KB
Loading...
Remedy Instructions and TSB
RCRIT-19V326-3289.pdf 414.749KB
Loading...
Miscellaneous Document – SAFETY RECALL 19V-326 (H208) – Shop Foreman Presentation Slide 8
RMISC-19V326-2303.pdf 135.349KB
Loading...
Miscellaneous Document – Presentation Slide – 2014-2015 MY F-TYPE SAFETY RECALL H208
RMISC-19V326-3983.pdf 125.631KB
Loading...
Manufacturer Notices(to Dealers,etc) – SAFETY RECALL H208 (NHTSA 19V-326)
RCMN-19V326-6688.pdf 205.091KB
Loading...
ISSUED Owner Notification Letter(Part 577)
RCONL-19V326-2477.pdf 289.475KB
Loading...
Recall Quarterly Report #1, 2019-2
RCLQRT-19V326-7567.PDF 211.153KB
Loading...
Recall Quarterly Report #2, 2019-3
RCLQRT-19V326-2167.PDF 211.257KB
Loading...
Recall Quarterly Report #3, 2019-4
RCLQRT-19V326-6113.PDF 211.348KB
Loading...
Latest Recalls Documents
For the Latest and Most Recent Recalls Information Visit the link below…
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=19V326&docType=RCL
- 5 IN 1 DIAGNOSTIC SCANNER: This is an OBDII scanner and 4 systems diagnostic tool. The AUTOPHIX 3210 PRO Bluetooth Auto Scanner not only has OBDII diagnostic function, but can also be used as an ABS/SRS/transmission scanner and check engine code reader. When it is an OBD2 scanner, you can use it to check if your car is ready for annual test via I/M preparation menu. In addition, the built-in DTC library, live data stream, data playback, performance testing and many more such functions are supported by it.
- RELIABLE CAR HEALTH MONITOR: Are you confused when the ABS/SRS/Transmission/Check Engine warning light is blinking? The AUTOPHIX 3210 PRO Bluetooth Scanner will help you to do a thorough scanning and inspecting of your car and find out the root cause, which saves your time and money. Tip:The warning light will be turned off after the problem is solved. Airbag crash/collision data cannot be cleared, even if you replace the airbag with a new one.
- QUICK DIAGNOSIS: The 3210 PRO is the newest 2024 Enhanced 4-System Bluetooth Code Reader that retrieves vehicle information, reads/clears trouble codes, and displays a 4-in-1 live data stream. You'll easily find out what's wrong with your car. In just a few minutes, you'll be in control of your car!
- EXCLUSIVE APP: Are you tired of the following with third party apps? For example: 1.need to download different apps for different cars? 2. require extra download fees? 3. only support a few functions? 4. can only use one of Android and iOS? Now!One AUTOPHIX 3210 PRO Scanner is enough to solve all the above problems. The must-have wireless/bluetooth automotive diagnostic tool/code reader for today's car owners. iPhone iOS, iPad, Android can be downloaded for free without any additional subscription fees.
- ADVANCED DATA FLOW DISPLAY:AUTOPHIX 3210 PRO Bluetooth code reader allows you to graphically display your vehicle's data flow instead of boring text, including engine coolant temperature, engine RPM, vehicle speed, absolute throttle position, control module voltage, etc. You can view different parameter values corresponding to different times. The advanced data streams provide useful information for entry-level professionals and diyers who can troubleshoot vehicle problems quickly and efficiently.
- 🎄【Easy to Use--Work out of box】+【FOXWELL 2024 New Version】 FOXWELL NT604 Elite scan tool is the 2024 new version from FOXWELL, which is designed for those car owners who want to figure out the cause issue before fixing the car problem via scanning the most common systems like abs srs engine and transmission.The NT604 Elite diagnostic tool comes with latest software, which can be used out of box. No need to waste time to download the software first.
- 🎅【Affordable】+【Reliable Car Health Monitor】 Will you be confused what happen when the warning light of abs/srs/transmission/check engine flashes? Instead of taking your cars to dealership, this foxwell scanner will help you do a thorough scanning and detection for your cars and pinpoint the root cause. It will t-urn off the warning light car after the problem is fixed.👉TIPS: Airbag crash/collision data can NOT be cleared even you replace the new airbag.
- 🎄【5 in 1 Diagnostic Scanner】Compared with those auto scanners (50-100), NT604 Elite code scanner not only includes their OBDII diagnosis but also it can be an abs/srs scanner, transmission and check engine code reader. When it’s an odb2 scanner, you can use it to check if your car is ready for annual test through I/M readiness menu. In addition, live data stream, built-in DTC library, data play back and print, all these features are a big plus for it.
- 🎅【Fantastic AUTOVIN】+【No extra software fee】Through the AUTOVIN menu, this NT604 Elite car scanner allows you to get your V-IN and vehicle info rapidly, no need to take time to find your V-IN and input one by one. What's more, the NT604 Elite abs srs scanner supports 60+ car makes from worldwide (America/Asia/Europe). You don’t need to pay extra software fee.
- 🎄【Solid protective case KO plastic carrying bag】+ 【Lifetime update】Almost all same price-level obd scanner diagnostic tool only offers plastic bag to hold on the scanner.However, NT604 Elite automotive scanner is equipped with solid protective case, preventing your obd2 scanner from damage. Then you don’t need to pay extra money to buy a solid toolbox.
- 2024 Best Choice for ABS Bleeder Scan Tool - Was the brake pedal always slowly sinking down or becoming loose? This abs brake bleeding scan tool will bleed the brake system by cycling the pump and valves to achieve a tight brake pedal. It's the most affordable obd2 scanner with abs auto bleed function you can find. With the clear step by step instruction, even a beginner can use it. Coverage check on FOXWELL official site: Support- Diagnostic Coverage List.
- More Than a Entry Level OBD Scanner, Ideal for Home Mechanics - Based on the NT301 FOXWELL Scanner, NT630 Plus takes OBD diagnostics to the next level by customizing all functions for ABS and SRS systems. This srs abs scanner provides in-depth insights on error code diagnosis, wheel speed sensor live data, airbag circuits and cable connectors monitor, module activation and etc. It's an total game-changer in resolving ABS SRS issues.
- No More Higher End Service than You Needed - One NT630 Plus is enough! This obd2 scanner with abs and srs takes depth diagnosis on Anti-Lock Brake System & Supplemental Restraint System, and also performs daily required resetting services which same priced scanners cannot do. Like Airbag light reset/ SAS(Steering Angle Sensor) adjustment/ Oil light reset functions. this car scanner will help the part to operate normally after the faults repaired.
- Also can Work like NT301 - The NT630 Plus abs code reader connect to the OBD2 port directly. It will diagnose all obd2 modules instantly, displays the live data, locates bad sensors and I/M readiness status before the annual inspection. Guides you to do the maintenance work, reduces the potential driving risk and keep a peak performance on the road.
- Complicate? Unreadable? - Intuitive LCD display with clear operate instructions, even a beginner can diagnose the car faults with the NT630 Plus. Ergonomic Touch with anti-collision and anti-slip cover design, comfortable for daily car diagnose work. Unique button press sound will provide the overall tactile and visual experience to notice you a task has been completed or a command has been executed.
- 🎉【2024 Upgraded Ver. of AL519/ ML519/ ML619】Autel develops the brand-new AutoLink AL619 as the advanced ver. of Autel ML519, AL519, AL319, MS309. This AL619 OBD2 scanner can scan ABS & SRS systems, and support 10 Modes of OBD II Diagnostics Function on Worldwide Vehicles to read, erase codes and turn off the MIL, ABS, SRS warning lights so that you can better maintain your car when related malfunctions occur and make your vehicle ready for the annual test.
- 🎉【Accurate ABS/ SRS Diagnostics Functions】The ABS/ SRS diagnostic function is used to retrieve and clear codes from the ABS/ SRS systems. It can read and clear DTCs, show definitions of each code, display live data of multiple sensors in the graph to locate fault causes, and assist home mechanics to do the proper repair and clear ABS & Airbag warning lights. Diagnoses ABS/ SRS system codes on most 1996 and newer major vehicle models. Please email 📩 immoautel @ outlook. com 📩 for help.
- 🎉【All 10 Modes of OBD II Diagnostics Function】The OBD II Diagnostics function is a fast-access option that allows you to carry out a quick test on the engine system of OBD II vehicles. Read Codes, Erase Codes, Live Data, Freeze Frame, Retrieving I/M Readiness Status, O2 Monitor Test, On-Board Monitor Test, DTC Lookup, Component Test, Viewing Vehicle Information, Modules Present.
- 🎉【Live Data and Freeze Frame Data】With Live Data functions, Autel AL619 OBD2 diagnostic code reader allows you to view the live PID (Parameter Identification Data) of the vehicle's computer module(s) in text, graph to check the status of various sensors. And Freeze Frame Data enables you to view the vehicle's operating parameters at the moment a DTC is detected. These information will aid the technician by allowing the parameters to be duplicated for diagnostic and repair purposes.
- 🎉【DTC Lookup Feature】Besides showing you the code’s definition while you are reading the diagnostic trouble codes, AL619 features comparably user-friendly DTC Lookup Function which enables you to retrieve the definitions of any error codes from the large database of AL619, saving you from the hassle of wasting time searching definition of every code via Google.
- 💻Note: (About UPDATE) ANCEL FX2000 car scanner diasgnostic tool can be used directly as it comes with existed software, You don't need to register or update beforethe first use. It's recommended to update your scanner only when it fails to work on your car, or it's slow to load all menus or if you need newer software version. 📢Software update supports WIN XP, 7, 8, 10 operation systems only., but not for Mac and ios system.
- 🔧【PLUG AND PLAY - EASY TO USE】 : ANCEL FX2000 car scanner only takes 3 steps to connect to the car for diagnosis without cumbersome operations. The latest FX2000 scan tool is equipped with a one-key diagnosis function, which can automatically identify the model and year of your car, and automatically diagnose the car. Even beginners can use it to read the data and find out what the fault codes mean.
- 🚗【FULL OBD-LEVEL DIAGNOSTICS TOOL】: Quickly determines the cause of engine system faults, reads current, permanent and pending codes. After the repair, clears the codes and turns off the warning light. In addition, the FX2000 engine code reader also displays important OBD II advanced data such as fuel, live data and other manufacturer-specific parameters in real time to ensure that the engine ECU is operating correctly and safely, saving vehicle owners a lot of time and money in maintenance.
- 🚙【TRANSMISSION FAULT DIAGNOSTIC TOOL】: Some noises come from the transmission? Ancel obd2 scanner will read fault codes, display live transmission system data (fluid temperature, fluid pump, clutch actuation, pressure, etc.), and ensures transmission performance is optimal for vehicle speed and load. It provides detailed TCM data of the vehicle, so you can quickly and accurately find existing or potential problems.
- 🚐【FIND OUT SRS WRONG】: ANCEL FX2000 automotive scanner is able to read and clear fault codes in the SRS (airbag) and turn off the warning light to make sure the system is working correctly and safely. This odb2 scanner also displays a live graphical data stream of the supplemental restraint system (air bag), which allows you to analyze and verify that the air bag system is working properly.
- [Transform Your Car Care Experience] - With BLCKTEC, instantly become your own professional mechanic. Effortlessly read and clear your car’s trouble codes and check engine light, ensuring your vehicle stays in top condition.
- [Empower Yourself with Comprehensive Diagnostics] - Unlock the full potential of your vehicle with the BLCKTEC 430. Access detailed diagnostics previously exclusive to professional mechanics’ OBD2 scan tools, including ABS, Airbag, SRS, TPMS codes, and beyond, right at your fingertips.
- [Drive with Confidence] - The BLCKTEC 430 is more than just a car code reader; it's your personal vehicle health advisor. Receive tailored repair reports with potential causes and verified solutions for your specific make and model, guiding you to the right fix every time.
- [Seamless Connectivity, Ultimate Convenience] - Experience the freedom of wireless diagnostics with this portable car scanner. Easily connect via Bluetooth to our intuitive sensor, and enjoy all the functionalities of high-end scan tools without the clutter of wires, directly from your smartphone or tablet.
- [DIY Repairs Made Easy] - Navigate car maintenance with ease using our premium app. Access a vast library of easy-to-follow repair videos, guiding you through each step of the repair process, compatible with both iOS & Android devices.
- 【Buy with Confidence】 As a America's No.1 diagnostic tool brand, Innova stands for innovation, quality, and accessibility in the automotive diagnostic industry. We are known for developing cutting-edge diagnostic tools that are user-friendly, reliable, and made for US by Americans.
- 【Unleash Your Drive's Potential】Much more than a car code reader, the 6100P scanner effectively reads and erases engine, ABS, SRS, and transmission codes for popular US car makes such as Ford, Chevy, Dodge, GM, etc. When the traction light is constantly on, the ability to really detect where the problem is concerning brakes and airbags enables you to make sure all safety measures in place before putting yourself in harm's way.
- 【Your Car's Health Doctor】Easily view procedures or send commands for oil change, mileage or driving time reset for most 1996 and newer OBD2 vehicles. It also monitors your oil level and oil life status, ensuring optimal vehicle health.
- 【alternator Test】The Innova 6100P scanner is perfect for assessing the performance of the alternator in your hybrid, car, SUV, minivan, or light truck diesel as well. During rough winters and scorching summers, this diagnostic tool will be invaluable when trying to root out start-up issues.
- 【Drive with Confidence and Peace】Quickly identify if your vehicle needs immediate attention with our Code Severity Levels function. This feature helps you understand whether you need to fix an issue immediately or if it can wait until you get home, keeping warning lights at bay.
- [ABS & SRS Scanner with Active Test] The ABS/ SRS diagnostic tool Read & clear DTCs, displays live data in a graph to locate the cause of faults and assists the home mechanic with repairs and clearing ABS and airbag warning lights. Active test sensors, valves or solenoids etc. and tracks any threats in real time. It is invaluable to have a diagnostic tool with Active Test feature that you will never find on similar ABS/ SRS scanners.
- 【3 HOP Reset Services 】Easy to set up 3 regular reset services for Oil Light, Battery Management System, and Steering Angle Position. With this obd2 scanner, you can reset the oil service light and reset pre-programmed mileage intervals for energy efficiency; adjust or reset the steering angle position to keep steering aligned; and clear the original low battery fault information. No need to leave home for shop-quality car maintenance.
- 【All OBD2 Test Modes 】 This ABS & SRS scan tool is also a full featured obd2 code reader, allowing a quick test of the engine system of OBD II vehicles, can Read/Clear engine light codes, Live Data, Freeze Frame, Retrieving I/M Readiness Status, O2 Monitor Test, On-Board Monitor Test, Evap Test, Read Vehicle Information, and help pass smog test for most post-1996 OBD2/CAN vehicles.
- [DTC LookUp Library] Can't read the code? Go to the DTC LookUp Library. The Topdon AL600 OBD2 scanner offers a wealth of code definitions so you don't have to look them up in a list or database, and the HELP function takes you to diagnostic tips for possible fixes, saving time searching for repair materials online. No other scan tool or code reader under $100 offers this level of assistance.
- [User-Oriented] You'll love the feel of this automotive scanner, with black rubber grips all around the outer edges for durability and to withstand accidental drops. With its easy access menu, you can operate all functions in minutes with just a few button presses. The 3-color LEDs give you a intuitive indication of the OBD2 test results in a second. 3 shortcut keys, one key to read/clear DTCs and a one-touch smoke status check make it easy to use even for beginners.
- 【Great Ideal For Every Car Owner】Prefect choice for your father, husband, brother or boyfriend. EVERY CAR OWNER WILL NEED IT! It comes with h-igh-quality host with a strong box. Get LAUNCH CRP123 Elite car diagnostic scanner and give your lover a surprise!
- 【 Read & Clear/Reset Engine/ABS/SRS/Transmission Diagnostic Scan Tool 】LAUNCH CRP123 OBD2 Scanner can test Engine, Transmission, ABS and Airbag four systems, also reads and resets code, displays data stream graphic, stores and playbacks dynamic data stream,helps to quick analysis and diagnosis.
- 【 Error Fault Code Reader】Except the full 10 modes OBD2 diagnostic functions like, retrieving I/M readiness, Freeze Frame Data, Read Dynamic Data stream and V-ehicle Information, O2 Sensor Test, EVAP Test of F-uel Tank System (Mode 8) and Advanced On-board Monitoring (Mode 6), launch crp123 obd2 scanner can not only reveal what error codes your car is producing, but also erase your v-ehicle’s check engine light after problem fixed, the DTC help and explanation also tell you the exact problem.
- 【 Live Data Graphing + Read/Record/Playback Data stream + Print diagnostic data 】Live Data Graphing,more intuitive to know your vehicle’s problem.Large size Color Screen ;Print Function:Print the diagnose result easily; with user manual and register & update tutorial video uploaded in the link by us,you can Look up it anytime by ONE-CLICK.
- 【 Find Your Vehicles Here】Launch CRP123 obd2 scanner Supports mainstream vehicles on the world,fit for ACURA VW AUDI AUST FORD BENZ BMW CHRYSLER FIAT GM HOLDEN HONDA HYUNDAI INFINITI JAGUAR ISUZU KIA LANDROVER LEXUS MAZDA MITSUBISHI NISSAN OPEL PORSCHE SAAB SEAT SKODA SMART MERCEDES SPRINTER SUBARU SUZUKI SCION TOYOTA USA FORD VOLVO PEUGEOT CITROEN RENAULT EUROFORD.Etc.
- 🎁 New Elite Version🎁 Easy to Use--Work out of Box🎁Function as LAUNCH CRP123E 🎁 Lifetime Update🎁 5 YEARS Back Up.Note:1. The product is a four-system tool, unable to scan the whole system, 2. The automatic scanning function is only for obd2 vehicles after 2006, not all vehicles, 3. If it cannot be charged, it may be a problem with the charging cable, you can reach us to resend a charging cable, or it may be a product problem, we can resend it soon. If the product loads slowly, it may be a network problem, try switching to a better network. If you encounter any problems, please rea-ch us, we will help you solve until you are satisfied, thank you.
- [Engine/ABS/SRS/Transmission Diagnostic Tool]----The crp123 obd2 scanner is perfect balance of power and affordability, providing the ability to view preset, or user defined, live data streams for ENGINE, AT, ABS and SRS data, the ability to graph, record, replay and print data, read and resets codes for engine/abs/srs/transmission system.(Note: Does not work for other System and does not have Special services!)
- [Full OBDII Test Code Reader]----LAUNCH CRP123 scan tool supports all 10 modes of OBDII standard to ensure complete, accurate, system diagnosis. Read and Clear DTCs, do smog tests , I/M readiness and O2 sensor tests, Mode 06 EVAP system test, Mode 08 on-board test component test. And OBDII Code lookup tool and acronym database to assist and speed diagnosis and repair time.
- [Live Data Stream + Advanced OBDII Scanner + Lifetime Update]---- Launch crp123 scanner support for Generic OBDII Codes (P0, P2, P3 and U0); manufacturer specific codes (P1, P3 and U1); pending codes; freeze frame data; monitor and I/M readiness; live PCM stream data; graphing functionality for up to four (4) live data streams include the Engine Coolant Temperature, Long&Short Fuel Trim, the change of Accelerator Pedal Position Sensor , Throttle valve position , Generator load signal,Fuel Tank Pressure , Engine RPM, Intake Ait Temperature and so on; clears DTC codes and turns off the MIL; resets monitors; provides Data Link Connector (DLC) location hints.
- [Extensive Vehicle Coverage + 10 Languages]--The LAUNCH CRP123 reads data from ENGINE, TRANSMISSION, ABS and SRS systems from Asian, US and European manufacturers. Coverage includes for Suzuki, for Honda, for Mitsubishi, for Nissan, for Toyota,for Mazda, for Hyundai,for Kia, for Subaru,for Infiniti, for Lexus, for Acura, for Isuzu, for Ford, for GM, for Chrysler, for Benz, for BMW, for VW, for Opel, for Volvo, for Fiat,for Land Rover, for Seat, for Skoda, for Audi,for Porsche, for Saab, for Jaguar and many others. Support 10 different languages.Note: Please rea-ch us your VIN to Check Compatibility before purchase.
Last update on 2024-04-09 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.