“This site contains affiliate links for which OEMDTC may be compensated” |
July 21, 2022 NHTSA CAMPAIGN NUMBER: 22V524000
Seat Belt Pretensioners May Not Restrain Properly
Improperly restrained occupants have an increased risk of injury during a crash.
NHTSA Campaign Number: 22V524
Manufacturer Jaguar Land Rover North America, LLC
Components SEAT BELTS
Potential Number of Units Affected 176
Summary
Jaguar Land Rover North America, LLC (Jaguar) is recalling certain 2022 Jaguar F-Type, F-Pace, and XF vehicles. The driver and front passenger seat belt pretensioners may be damaged, which can cause the seat belts to not properly restrain occupants.
Remedy
Dealers will inspect and replace the front seat belt assemblies, as necessary, free of charge. Owner notification letters were mailed September 15, 2022. Owners may contact Jaguar customer service at 1-800-452-4827. Jaguar’s number for this recall is H412.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
Check if your Jaguar has a Recall
DESCRIPTION OF DEFECT
A concern has been identified on certain 2022MY Jaguar F-TYPE, XF, and F-PACE vehicles where a damaged front seat belt pretensioner tube may have been installed on the seat belt retractor.
AFFECTED VEHICLE RANGE
F-TYPE
Model Year: ………………….. 2022
VIN: ………………………………… SAJDD1EE9NCK78757 – SAJD85EE3NCK79169
XF
Model Year: ………………….. 2022
VIN: ………………………………… SAJB4GX1NC91515 – SAJBL4GX5NCY91713
F-PACE
Model Year: ………………….. 2022
VIN: ………………………………… SADCJEX2NA693574 – SADCZ2EE0NA694892
A total of approximately 176 vehicles in the United States and Federalized Territories.
EFFECT OF VEHICLE OPERATION
A damaged front seat belt pretensioner tube could prevent the pretensioner from correctly operating by not pre-tensioning the seat belt in the event of an accident where it would normally operate. This may result in a reduced level or complete loss of pre-tensioning in the event of a crash and increased occupant injury.
SERVICE PROGRAM/REWORK ACTION
Owners will be notified by mail and instructed to take their vehicle to an authorized retailer who will inspect the seat belt pretensioner tube for damage. If damage is identified, the seat belt retractor will be replaced. There will be no charge to the owners for this action under this program.
OWNER NOTIFICATION
Owner notification is expected to occur on or before the week of September 16, 2022.
ACTION TO BE TAKEN
Check the Jaguar Land Rover Warranty Portal to make sure affected vehicles are correctly identified prior to starting this campaign. The Warranty Portal will be updated to reflect only those vehicles affected.
Retailers/authorized repairers are required to Quarantine affected new vehicles that are within your control and refrain from releasing the vehicles for new vehicle sale pending completion of the rework action. Affected vehicles already with customers should be updated at the next available opportunity. JLR North America recommends that affected sales demonstrator and loaner vehicles are repaired before use and that used vehicles are repaired before sale. Retailers/authorized repairers who choose to proceed against this recommendation, where legally permitted, must clearly and conspicuously disclose the open recall to the applicable customers.
A Safety Recall will be published when repair instructions are finalized, and any required parts have been procured.
Retailers/authorized repairers are reminded that they must not sell vehicles identified as affected by this campaign until such time as the repair has been successfully completed.
After the Safety Recall is launched, visit the British Brands Sales Suite (BBSS) website for a list of affected vehicles at your retailer/authorized repairer.
Chronology :
Following a notification from Autoliv that a defect had been identified during their manufacturing process that caused damage to a small number of front seat belt pretentioner tubes, Jaguar Land Rover (JLR) opened a PSCC (Product Safety & Compliance Committee) investigation on May 25, 2022. The PSCC requested that Vehicle Assembly Plants conduct an exercise to identify if they had received any parts from the batches Autoliv deemed at risk and the population of affected vehicles that may have received parts from these batches. On June 1, 2022, Autoliv presented the issue to the PSCC, Autoliv explained the issue that had been identified on one of their seatbelt production lines and the potential impact on the component functionality. During June, each vehicle assembly plant conducted detailed research to identify which batches deemed at risk by Autoliv had been consumed and the specific vehicle identification numbers of vehicles that may have received parts from these batches. In July, the qualification/identification of damaged parts was confirmed, and the subject matter experts within JLR confirmed the impact of damaged pretentioners on the Supplementary Restraints System (SRS) and on occupant protection. At the PSCC of July 13, 2022, the scope was discussed along with exposure and vehicle disposition confirmed. Based on the feedback provided, the PSCC progressed the issue to the Recall Determination Committee (RDC) for review. The RDC reviewed the issue on July 14, 2022, and concluded that it represented an unreasonable risk to safety and a voluntary safety recall should be conducted to inspect the pretensioner on all vehicles identified to be at risk of receiving a damaged pretensioner, and if a damaged component is identified, the seatbelt assembly should be replaced. There are no warranty claims, field or service reports, or other information (such as the numbers of deaths and/or injuries), associated with this recall.
3 Affected Products
Vehicles
MAKE | MODEL | YEAR |
JAGUAR | F-PACE | 2022 |
JAGUAR | F-TYPE | 2022 |
JAGUAR | XF | 2022 |
15 Associated Documents
Recall 573 Report – July 22, 2022
RCLRPT-22V524-7687.PDF 220.016KB
Recall Acknowledgement
RCAK-22V524-4876.pdf 645.497KB
Recall 573 Report
RCLRPT-22V524-3036.PDF 219.984KB
Recall 573 Report – July 22, 2022
RCLRPT-22V524-3302.PDF 220.016KB
Recall 573 Report – August 3, 2022
RCLRPT-22V524-3634.PDF 220.158KB
Presentation Slide
RMISC-22V524-2287.pdf 81.024KB
Manufacturer Notices(to Dealers,etc)
Presentation Slide
RMISC-22V524-6643.pdf 395.148KB
Remedy Instructions and TSB
RCRIT-22V524-0663.pdf 2359.695KB
SAFETY RECALL N720 H412 – Autoliv Seat belt Retractor Functionality
RMISC-22V524-1433.pdf 82.391KB
ISSUED Owner Notification Letter(Part 577)
RCONL-22V524-9546.pdf 275.162KB
Remedy Instructions and TSB
RCRIT-22V524-0206.pdf 2226.515KB
Recall Quarterly Report #1, 2022-3
RCLQRT-22V524-9293.PDF 211.147KB
Recall Quarterly Report #2, 2022-4
RCLQRT-22V524-0311.PDF 211.252KB
Recall Quarterly Report #3, 2023-1
RCLQRT-22V524-4562.PDF 211.333KB
Latest Recalls Documents
For the Latest and Most Recent Recalls Information Visit the link below…
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=22V524&docType=RCL
- 5 IN 1 DIAGNOSTIC SCANNER: This is an OBDII scanner and 4 systems diagnostic tool. The AUTOPHIX 3210 PRO Bluetooth Auto Scanner not only has OBDII diagnostic function, but can also be used as an ABS/SRS/transmission scanner and check engine code reader. When it is an OBD2 scanner, you can use it to check if your car is ready for annual test via I/M preparation menu. In addition, the built-in DTC library, live data stream, data playback, performance testing and many more such functions are supported by it.
- RELIABLE CAR HEALTH MONITOR: Are you confused when the ABS/SRS/Transmission/Check Engine warning light is blinking? The AUTOPHIX 3210 PRO Bluetooth Scanner will help you to do a thorough scanning and inspecting of your car and find out the root cause, which saves your time and money. Tip:The warning light will be turned off after the problem is solved. Airbag crash/collision data cannot be cleared, even if you replace the airbag with a new one.
- QUICK DIAGNOSIS: The 3210 PRO is the newest 2024 Enhanced 4-System Bluetooth Code Reader that retrieves vehicle information, reads/clears trouble codes, and displays a 4-in-1 live data stream. You'll easily find out what's wrong with your car. In just a few minutes, you'll be in control of your car!
- EXCLUSIVE APP: Are you tired of the following with third party apps? For example: 1.need to download different apps for different cars? 2. require extra download fees? 3. only support a few functions? 4. can only use one of Android and iOS? Now!One AUTOPHIX 3210 PRO Scanner is enough to solve all the above problems. The must-have wireless/bluetooth automotive diagnostic tool/code reader for today's car owners. iPhone iOS, iPad, Android can be downloaded for free without any additional subscription fees.
- ADVANCED DATA FLOW DISPLAY:AUTOPHIX 3210 PRO Bluetooth code reader allows you to graphically display your vehicle's data flow instead of boring text, including engine coolant temperature, engine RPM, vehicle speed, absolute throttle position, control module voltage, etc. You can view different parameter values corresponding to different times. The advanced data streams provide useful information for entry-level professionals and diyers who can troubleshoot vehicle problems quickly and efficiently.
- 🎄【Easy to Use--Work out of box】+【FOXWELL 2024 New Version】 FOXWELL NT604 Elite scan tool is the 2024 new version from FOXWELL, which is designed for those car owners who want to figure out the cause issue before fixing the car problem via scanning the most common systems like abs srs engine and transmission.The NT604 Elite diagnostic tool comes with latest software, which can be used out of box. No need to waste time to download the software first.
- 🎅【Affordable】+【Reliable Car Health Monitor】 Will you be confused what happen when the warning light of abs/srs/transmission/check engine flashes? Instead of taking your cars to dealership, this foxwell scanner will help you do a thorough scanning and detection for your cars and pinpoint the root cause. It will t-urn off the warning light car after the problem is fixed.👉TIPS: Airbag crash/collision data can NOT be cleared even you replace the new airbag.
- 🎄【5 in 1 Diagnostic Scanner】Compared with those auto scanners (50-100), NT604 Elite code scanner not only includes their OBDII diagnosis but also it can be an abs/srs scanner, transmission and check engine code reader. When it’s an odb2 scanner, you can use it to check if your car is ready for annual test through I/M readiness menu. In addition, live data stream, built-in DTC library, data play back and print, all these features are a big plus for it.
- 🎅【Fantastic AUTOVIN】+【No extra software fee】Through the AUTOVIN menu, this NT604 Elite car scanner allows you to get your V-IN and vehicle info rapidly, no need to take time to find your V-IN and input one by one. What's more, the NT604 Elite abs srs scanner supports 60+ car makes from worldwide (America/Asia/Europe). You don’t need to pay extra software fee.
- 🎄【Solid protective case KO plastic carrying bag】+ 【Lifetime update】Almost all same price-level obd scanner diagnostic tool only offers plastic bag to hold on the scanner.However, NT604 Elite automotive scanner is equipped with solid protective case, preventing your obd2 scanner from damage. Then you don’t need to pay extra money to buy a solid toolbox.
- 2024 Best Choice for ABS Bleeder Scan Tool - Was the brake pedal always slowly sinking down or becoming loose? This abs brake bleeding scan tool will bleed the brake system by cycling the pump and valves to achieve a tight brake pedal. It's the most affordable obd2 scanner with abs auto bleed function you can find. With the clear step by step instruction, even a beginner can use it. Coverage check on FOXWELL official site: Support- Diagnostic Coverage List.
- More Than a Entry Level OBD Scanner, Ideal for Home Mechanics - Based on the NT301 FOXWELL Scanner, NT630 Plus takes OBD diagnostics to the next level by customizing all functions for ABS and SRS systems. This srs abs scanner provides in-depth insights on error code diagnosis, wheel speed sensor live data, airbag circuits and cable connectors monitor, module activation and etc. It's an total game-changer in resolving ABS SRS issues.
- No More Higher End Service than You Needed - One NT630 Plus is enough! This obd2 scanner with abs and srs takes depth diagnosis on Anti-Lock Brake System & Supplemental Restraint System, and also performs daily required resetting services which same priced scanners cannot do. Like Airbag light reset/ SAS(Steering Angle Sensor) adjustment/ Oil light reset and EPB service functions. this car scanner will help the part to operate normally after the faults repaired.
- Also can Work like NT301 - The NT630 Plus abs code reader connect to the OBD2 port directly. It will diagnose all obd2 modules instantly, displays the live data, locates bad sensors and I/M readiness status before the annual inspection. Guides you to do the maintenance work, reduces the potential driving risk and keep a peak performance on the road.
- Complicate? Unreadable? - Intuitive LCD display with clear operate instructions, even a beginner can diagnose the car faults with the NT630 Plus. Ergonomic Touch with anti-collision and anti-slip cover design, comfortable for daily car diagnose work. Unique button press sound will provide the overall tactile and visual experience to notice you a task has been completed or a command has been executed.
- 🎉【2024 Upgraded Ver. of AL519/ ML519/ ML619】Autel develops the brand-new AutoLink AL619 as the advanced ver. of Autel ML519, AL519, AL319, MS309. This AL619 OBD2 scanner can scan ABS & SRS systems, and support 10 Modes of OBD II Diagnostics Function on Worldwide Vehicles to read, erase codes and turn off the MIL, ABS, SRS warning lights so that you can better maintain your car when related malfunctions occur and make your vehicle ready for the annual test.
- 🎉【Accurate ABS/ SRS Diagnostics Functions】The ABS/ SRS diagnostic function is used to retrieve and clear codes from the ABS/ SRS systems. It can read and clear DTCs, show definitions of each code, display live data of multiple sensors in the graph to locate fault causes, and assist home mechanics to do the proper repair and clear ABS & Airbag warning lights. Diagnoses ABS/ SRS system codes on most 1996 and newer major vehicle models. Please email 📩 immoautel @ outlook. com 📩 for help.
- 🎉【All 10 Modes of OBD II Diagnostics Function】The OBD II Diagnostics function is a fast-access option that allows you to carry out a quick test on the engine system of OBD II vehicles. Read Codes, Erase Codes, Live Data, Freeze Frame, Retrieving I/M Readiness Status, O2 Monitor Test, On-Board Monitor Test, DTC Lookup, Component Test, Viewing Vehicle Information, Modules Present.
- 🎉【Live Data and Freeze Frame Data】With Live Data functions, Autel AL619 OBD2 diagnostic code reader allows you to view the live PID (Parameter Identification Data) of the vehicle's computer module(s) in text, graph to check the status of various sensors. And Freeze Frame Data enables you to view the vehicle's operating parameters at the moment a DTC is detected. These information will aid the technician by allowing the parameters to be duplicated for diagnostic and repair purposes.
- 🎉【DTC Lookup Feature】Besides showing you the code’s definition while you are reading the diagnostic trouble codes, AL619 features comparably user-friendly DTC Lookup Function which enables you to retrieve the definitions of any error codes from the large database of AL619, saving you from the hassle of wasting time searching definition of every code via Google.
- 💻Note: (About UPDATE) ANCEL FX2000 car scanner diasgnostic tool can be used directly as it comes with existed software, You don't need to register or update beforethe first use. It's recommended to update your scanner only when it fails to work on your car, or it's slow to load all menus or if you need newer software version. 📢Software update supports WIN XP, 7, 8, 10 operation systems only., but not for Mac and ios system.
- 🔧【PLUG AND PLAY - EASY TO USE】 : ANCEL FX2000 car scanner only takes 3 steps to connect to the car for diagnosis without cumbersome operations. The latest FX2000 scan tool is equipped with a one-key diagnosis function, which can automatically identify the model and year of your car, and automatically diagnose the car. Even beginners can use it to read the data and find out what the fault codes mean.
- 🚗【FULL OBD-LEVEL DIAGNOSTICS TOOL】: Quickly determines the cause of engine system faults, reads current, permanent and pending codes. After the repair, clears the codes and turns off the warning light. In addition, the FX2000 engine code reader also displays important OBD II advanced data such as fuel, live data and other manufacturer-specific parameters in real time to ensure that the engine ECU is operating correctly and safely, saving vehicle owners a lot of time and money in maintenance.
- 🚙【TRANSMISSION FAULT DIAGNOSTIC TOOL】: Some noises come from the transmission? Ancel obd2 scanner will read fault codes, display live transmission system data (fluid temperature, fluid pump, clutch actuation, pressure, etc.), and ensures transmission performance is optimal for vehicle speed and load. It provides detailed TCM data of the vehicle, so you can quickly and accurately find existing or potential problems.
- 🚐【FIND OUT SRS WRONG】: ANCEL FX2000 automotive scanner is able to read and clear fault codes in the SRS (airbag) and turn off the warning light to make sure the system is working correctly and safely. This odb2 scanner also displays a live graphical data stream of the supplemental restraint system (air bag), which allows you to analyze and verify that the air bag system is working properly.
- SIMPLIFYING CAR REPAIR - Our goal is to simplify your car repair process. Our device turns your smartphone into a powerful OBD2 scanner diagnostic tool, allowing you to quickly understand your vehicle's problem, view recommended fixes, and purchase the necessary parts for repair.
- EXPERIENCE PROFESSIONAL DIAGNOSTICS - BLCKTEC's enhanced vehicle diagnostics gives you access to advanced features typically found only on high-end scanners. With our car code reader you can read and clear engine codes, ABS (brakes), SRS (airbags), TPMS codes, and many more.
- RELIABLE AND ACCURATE RESULTS - Our car scanner utilizes the latest OBD2 technology to provide accurate and reliable diagnostic information, ensuring that you can trust the results you receive.
- COMPATIBLE WITH A WIDE RANGE OF VEHICLES - Our bluetooth OBD2 scanner works with most vehicles made after 1996, including cars, trucks, and SUVs, making it a versatile tool for any DIYer.
- USER-FRIENDLY APP - Our accompanying app is easy to use and navigate, with clear and concise information displayed in an easy-to-understand format. Available on IOS and Android.
- 【Buy with Confidence】 As a America's No.1 diagnostic tool brand, Innova stands for innovation, quality, and accessibility in the automotive diagnostic industry. We are known for developing cutting-edge diagnostic tools that are user-friendly, reliable, and made for US by Americans.
- 【Unleash Your Drive's Potential】Much more than a car code reader, the 6100P scanner effectively reads and erases engine, ABS, SRS, and transmission codes for popular US car makes such as Ford, Chevy, Dodge, GM, etc. When the traction light is constantly on, the ability to really detect where the problem is concerning brakes and airbags enables you to make sure all safety measures in place before putting yourself in harm's way.
- 【Your Car's Health Doctor】Easily view procedures or send commands for oil change, mileage or driving time reset for most 1996 and newer OBD2 vehicles. It also monitors your oil level and oil life status, ensuring optimal vehicle health.
- 【alternator Test】The Innova 6100P scanner is perfect for assessing the performance of the alternator in your hybrid, car, SUV, minivan, or light truck diesel as well. During rough winters and scorching summers, this diagnostic tool will be invaluable when trying to root out start-up issues.
- 【Drive with Confidence and Peace】Quickly identify if your vehicle needs immediate attention with our Code Severity Levels function. This feature helps you understand whether you need to fix an issue immediately or if it can wait until you get home, keeping warning lights at bay.
- [ABS & SRS Scanner with Active Test] The ABS/ SRS diagnostic tool Read & clear DTCs, displays live data in a graph to locate the cause of faults and assists the home mechanic with repairs and clearing ABS and airbag warning lights. Active test sensors, valves or solenoids etc. and tracks any threats in real time. It is invaluable to have a diagnostic tool with Active Test feature that you will never find on similar ABS/ SRS scanners.
- 【3 HOP Reset Services 】Easy to set up 3 regular reset services for Oil Light, Battery Management System, and Steering Angle Position. With this obd2 scanner, you can reset the oil service light and reset pre-programmed mileage intervals for energy efficiency; adjust or reset the steering angle position to keep steering aligned; and clear the original low battery fault information. No need to leave home for shop-quality car maintenance.
- 【All OBD2 Test Modes 】 This ABS & SRS scan tool is also a full featured obd2 code reader, allowing a quick test of the engine system of OBD II vehicles, can Read/Clear engine light codes, Live Data, Freeze Frame, Retrieving I/M Readiness Status, O2 Monitor Test, On-Board Monitor Test, Evap Test, Read Vehicle Information, and help pass smog test for most post-1996 OBD2/CAN vehicles.
- [DTC LookUp Library] Can't read the code? Go to the DTC LookUp Library. The Topdon AL600 OBD2 scanner offers a wealth of code definitions so you don't have to look them up in a list or database, and the HELP function takes you to diagnostic tips for possible fixes, saving time searching for repair materials online. No other scan tool or code reader under $100 offers this level of assistance.
- [User-Oriented] You'll love the feel of this automotive scanner, with black rubber grips all around the outer edges for durability and to withstand accidental drops. With its easy access menu, you can operate all functions in minutes with just a few button presses. The 3-color LEDs give you a intuitive indication of the OBD2 test results in a second. 3 shortcut keys, one key to read/clear DTCs and a one-touch smoke status check make it easy to use even for beginners.
- 【Great Ideal For Every Car Owner】Prefect choice for your father, husband, brother or boyfriend. EVERY CAR OWNER WILL NEED IT! It comes with h-igh-quality host with a strong box. Get LAUNCH CRP123 Elite car diagnostic scanner and give your lover a surprise!
- 【 Read & Clear/Reset Engine/ABS/SRS/Transmission Diagnostic Scan Tool 】LAUNCH CRP123 OBD2 Scanner can test Engine, Transmission, ABS and Airbag four systems, also reads and resets code, displays data stream graphic, stores and playbacks dynamic data stream,helps to quick analysis and diagnosis.
- 【 Error Fault Code Reader】Except the full 10 modes OBD2 diagnostic functions like, retrieving I/M readiness, Freeze Frame Data, Read Dynamic Data stream and V-ehicle Information, O2 Sensor Test, EVAP Test of F-uel Tank System (Mode 8) and Advanced On-board Monitoring (Mode 6), launch crp123 obd2 scanner can not only reveal what error codes your car is producing, but also erase your v-ehicle’s check engine light after problem fixed, the DTC help and explanation also tell you the exact problem.
- 【 Live Data Graphing + Read/Record/Playback Data stream + Print diagnostic data 】Live Data Graphing,more intuitive to know your vehicle’s problem.Large size Color Screen ;Print Function:Print the diagnose result easily; with user manual and register & update tutorial video uploaded in the link by us,you can Look up it anytime by ONE-CLICK.
- 【 Find Your Vehicles Here】Launch CRP123 obd2 scanner Supports mainstream vehicles on the world,fit for ACURA VW AUDI AUST FORD BENZ BMW CHRYSLER FIAT GM HOLDEN HONDA HYUNDAI INFINITI JAGUAR ISUZU KIA LANDROVER LEXUS MAZDA MITSUBISHI NISSAN OPEL PORSCHE SAAB SEAT SKODA SMART MERCEDES SPRINTER SUBARU SUZUKI SCION TOYOTA USA FORD VOLVO PEUGEOT CITROEN RENAULT EUROFORD.Etc.
- 🎁 New Elite Version🎁 Easy to Use--Work out of Box🎁Function as LAUNCH CRP123E 🎁 Lifetime Update🎁 5 YEARS Back Up.Note:1. The product is a four-system tool, unable to scan the whole system, 2. The automatic scanning function is only for obd2 vehicles after 2006, not all vehicles, 3. If it cannot be charged, it may be a problem with the charging cable, you can reach us to resend a charging cable, or it may be a product problem, we can resend it soon. If the product loads slowly, it may be a network problem, try switching to a better network. If you encounter any problems, please rea-ch us, we will help you solve until you are satisfied, thank you.
- [Engine/ABS/SRS/Transmission Diagnostic Tool]----The crp123 obd2 scanner is perfect balance of power and affordability, providing the ability to view preset, or user defined, live data streams for ENGINE, AT, ABS and SRS data, the ability to graph, record, replay and print data, read and resets codes for engine/abs/srs/transmission system.(Note: Does not work for other System and does not have Special services!)
- [Full OBDII Test Code Reader]----LAUNCH CRP123 scan tool supports all 10 modes of OBDII standard to ensure complete, accurate, system diagnosis. Read and Clear DTCs, do smog tests , I/M readiness and O2 sensor tests, Mode 06 EVAP system test, Mode 08 on-board test component test. And OBDII Code lookup tool and acronym database to assist and speed diagnosis and repair time.
- [Live Data Stream + Advanced OBDII Scanner + Lifetime Update]---- Launch crp123 scanner support for Generic OBDII Codes (P0, P2, P3 and U0); manufacturer specific codes (P1, P3 and U1); pending codes; freeze frame data; monitor and I/M readiness; live PCM stream data; graphing functionality for up to four (4) live data streams include the Engine Coolant Temperature, Long&Short Fuel Trim, the change of Accelerator Pedal Position Sensor , Throttle valve position , Generator load signal,Fuel Tank Pressure , Engine RPM, Intake Ait Temperature and so on; clears DTC codes and turns off the MIL; resets monitors; provides Data Link Connector (DLC) location hints.
- [Extensive Vehicle Coverage + 10 Languages]--The LAUNCH CRP123 reads data from ENGINE, TRANSMISSION, ABS and SRS systems from Asian, US and European manufacturers. Coverage includes for Suzuki, for Honda, for Mitsubishi, for Nissan, for Toyota,for Mazda, for Hyundai,for Kia, for Subaru,for Infiniti, for Lexus, for Acura, for Isuzu, for Ford, for GM, for Chrysler, for Benz, for BMW, for VW, for Opel, for Volvo, for Fiat,for Land Rover, for Seat, for Skoda, for Audi,for Porsche, for Saab, for Jaguar and many others. Support 10 different languages.Note: Please rea-ch us your VIN to Check Compatibility before purchase.
Last update on 2024-04-09 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
SEOCONTENT-START
BODY & CHASSIS SAFETY RECALL N720 H412 – Autoliv Seat belt Retractor Functionality • Seatbelt pretensioner inspection • Using a suitable mirror, carefully inspect the pretensioner for any damage where the activator tube mounts to the seatbelt real assembly. • Any sign of damage requires a seatbelt assembly replacement.
**************************************************************************************************************
N720 H412 SAFETY RECALL –SEAT BELT RETRACTOR FUNCTIONALITY SAFETY RECALL N720 H412 – SEAT BELT RETRACTOR FUNCTIONALITY AFFECTED MODELS 22-23MY F-PACE, F-TYPE, and XF 22-23MY RR Velar, RR Sport, Discovery Sport, Discovery, and Defender VOLUME AFFECTED H412 USA 176 H412 Canada 113 N720 USA 4,927 N720 Canada 645 REPAIR The front seat belt pretensioner tube may have been damaged during the manufacturing process. Less than 1% of vehicles are expected to have defective parts. Retailers will inspect the seat belt pretensioner tube for damage and if damage is identified, following instructions in the bulletin, will replace any defective parts. REPAIR TIME Inspect between 0.3 and 1.1 hrs. Inspect and Repair between 0.5 and 1.4 hrs + DIDO CAMPAIGN LAUNCH Retailer Notification only was issued August 4th, 2022. N720 – NAS22.08.005 USA NAS22.08.006 CAN H412 – NAS22.08.003 USA NAS22.08.004 CAN Repair bulletin target publication date is August 15th, 2022 Notes For sold cars, customers will be notified by direct mail following the normal Recall process.
**************************************************************************************************************
N720 H412 SAFETY RECALL – Autoliv Seat belt Retractor Functionality SAFETY RECALL N720 H412 – Autoliv Seat belt Retractor Functionality AFFECTED MODELS 22-23MY F-PACE, F-TYPE, and XF 22MY RR Sport 22-23MY RR Velar, Discovery Sport, Discovery, and Defender VOLUME AFFECTED H412 USA 176 H412 Canada 113 N720 USA 4,927 N720 Canada 645 REPAIR The front seat belt pretensioner tube may have been damaged during the manufacturing process. Retailers will inspect the seat belt pretensioner tube and if damage is identified, following instructions in the bulletin, will replace any defective parts. REPAIR TIME Between 0.3 to 1.4 hrs + DIDO CAMPAIGN LAUNCH August 19th, 2022 Notes The recall repair bulletin has been published to TOPIx. There are 34 affected vehicles in dealer inventory that need to be rectified before sale. <1% of vehicles are expected to fail inspection and require a new part.
**************************************************************************************************************
SAFETY RELATED RECALL Global Recall Action Number: H412 Subject: Autoliv Seatbelt Retractor Functionality Publication No.: H412 Model: F-PACE (X761) Model Year: 2022 – 2023 Model: F-TYPE (X152) Model Year: 2022 Model: XF (X260) Model Year: 2022 Date of Issue: 19 August 2022 To: Jaguar Land Rover (JLR) North America, LLC – USA and Canada For the Attention of: The approved JLR retailer/authorized repairer Important: NOTE: The information in this campaign is intended for use by trained, professional technicians with the knowledge, tools, and equipment required to do the job properly and safely. It informs these technicians of conditions that may occur on some vehicles or provides information that could assist in proper vehicle service. The procedures should not be performed by ‘do-it-yourselfers’. If you are not a JLR retailer/authorized repairer, do not assume that a condition described affects your vehicle. Contact an authorized JLR retailer/authorized repairer to determine if this campaign applies to a specific vehicle DESCRIPTION OF ISSUE AND THE EFFECT ON VEHICLE OPERATION A potential concern has been identified on specific vehicles within the above vehicle range. A concern has been identified on certain 2022 model year F-TYPE, XE and XF vehicles and certain 2022 and 2023 model year FPACE vehicles where a damaged front seatbelt pretensioner tube may have been installed on the seatbelt retractor. The damaged tube could prevent the pretensioner from correctly operating by not pre-tensioning the seatbelt in the event of an accident where it would normally operate. This may result in a reduced level or complete loss of pre-tensioning in the event of a crash and increased occupant injury. REGULATORY INFORMATION JLR North America, LLC and JLR Canada ULC have informed the National Highway Traffic Safety Administration (NHTSA) and Transport Canada (TC) of their intent to perform a Safety Recall on certain 2022 model year F-TYPE, XE and XF vehicles and certain 2022 and 2023 model year F-PACE vehicles imported into the United States and Canadian markets. Information relating to this Safety Recall will be posted on the NHTSA and TC websites. United States Federal regulations require that retailers/authorized repairers must be notified within a reasonable time after the manufacturer decides that a defect that relates to motor vehicle safety or a non-compliance exists. United States Federal Law requires retailers/authorized repairers to complete any outstanding Safety Recall before a new vehicle is delivered to the buyer or lessee. Violation of this requirement by a retailer/authorized repairer, in the USA only, could result in a maximum civil penalty of up to the equivalent of $24,423.00 USD per violation and the equivalent of $122,106,996.00 USD for a related series of violations. This Safety Recall serves as notification to all retailers/authorized repairers in the United States and Federalized Territories and Canada that any affected new vehicles may not be sold and delivered for customer use until the Safety Recall repair is completed. JLR North America, LLC / JLR Canada ULC recommends that affected sales demonstrator and loaner vehicles are repaired before use, and that used vehicles are repaired before sale. Retailers/authorized repairers who choose to proceed against this recommendation, where legally permitted, must clearly and conspicuously disclose the open Safety Recall notice to the applicable customers. ACTION TO BE TAKEN JLR has taken the decision to recall affected vehicles to repair the vehicle. Visit the British Brands Sales Suite (BBSS) website for a list of affected vehicles at your retailer/authorized repairer. Following procedures appropriate to your market and as required by local legislation, owners of affected vehicles should be contacted requesting that the owner contact their nearest retailer/authorized repairer as soon as possible to arrange for the repair to be completed. The National Sales Companies (NSCs), Importer, Regional Office or Government agency will contact the customers. If you have any questions about this process, please contact your NSC/Importer or Regional Office for more information. Check the JLR Warranty Portal to make sure affected vehicles are correctly identified prior to starting this campaign. The Warranty Portal will be updated to reflect only those vehicles affected. Retailers/authorized repairers are reminded that they must not sell vehicles identified as affected by this campaign until such time as the repair has been successfully completed. An owner may indicate that a repair has already been completed for this concern, in which case the full cost of the repair should be reimbursed. Refer to the warranty section of this campaign for details of the Customer Reimbursement and Related Damage Process. At the time of confirming a booking for a vehicle repair, make sure you check the Warranty Portal to confirm if there are any other outstanding campaigns, to make sure the correct parts are available and adequate workshop time is allocated for repairs to be completed in one visit. For information purposes, a Technical Question and Answer document is attached. Yours faithfully Steve Oldham Global Customer Service Quality Director SERVICE INSTRUCTION – H412 NOTE: The information in this campaign is intended for use by trained, professional technicians with the knowledge, tools, and equipment required to do the job properly and safely. It informs these technicians of conditions that may occur on some vehicles or provides information that could assist in proper vehicle service. The procedures should not be performed by ‘do-it-yourselfers’. If you are not a Jaguar Land Rover (JLR) retailer/authorized repairer, do not assume that a condition described affects your vehicle. Contact an authorized JLR retailer/authorized repairer to determine if this campaign applies to a specific vehicle Parts Information Any required parts should be ordered through JLR in the normal manner, however, for this campaign, parts should be claimed for using the Customer Reimbursement and Related Damage Process – See the Customer Reimbursement and Related Damage Process section below for further details. SROs – XF vehicles Description Model SRO Time Front seatbelt retractors – Inspect pair – No further action XF 05.10.50 0.5 Front seatbelt retractors – Inspect pair – Renew single XF 05.10.70 0.7 Front seatbelt retractors – Inspect pair – Renew pair XF 05.10.80 0.8 Drive in/drive out XF 10.10.10 0.2 NOTE: Repair procedures are under constant review, and therefore times are subject to change; those quoted here must be taken as guidance only. Always refer to TOPIx to obtain the latest repair time. SROs – XE vehicles Description Model SRO Time Front seatbelt retractors – Inspect pair – No further action XE 05.10.40 0.4 Front seatbelt retractors – Inspect pair – Renew single XE 05.10.60 0.6 Front seatbelt retractors – Inspect pair – Renew pair XE 05.10.70 0.7 Drive in/drive out XE 10.10.10 0.2 NOTE: Repair procedures are under constant review, and therefore times are subject to change; those quoted here must be taken as guidance only. Always refer to TOPIx to obtain the latest repair time. SROs – F-PACE vehicles Description Model SRO Time Front seatbelt retractors – Inspect pair – No further action F-PACE 05.10.50 0.5 Front seatbelt retractors – Inspect pair – Renew single F-PACE 05.10.70 0.7 Front seatbelt retractors – Inspect pair – Renew pair F-PACE 05.10.80 0.8 Drive in/drive out F-PACE 10.10.10 0.2 NOTE: Repair procedures are under constant review, and therefore times are subject to change; those quoted here must be taken as guidance only. Always refer to TOPIx to obtain the latest repair time. SROs – F-TYPE vehicles Description Model SRO Time Description Model SRO Time Front seatbelt retractors – Inspect pair – No further action F-TYPE 05.10.50 0.5 Front seatbelt retractors – Inspect pair – Renew single F-TYPE 05.10.60 0.6 Front seatbelt retractors – Inspect pair – Renew pair F-TYPE 05.10.70 0.7 Drive in/drive out F-TYPE 10.10.10 0.2 NOTE: Repair procedures are under constant review, and therefore times are subject to change; those quoted here must be taken as guidance only. Always refer to TOPIx to obtain the latest repair time. Warranty Information Warranty claims should be submitted quoting program code H412 with option code X. In this instance it will also be necessary to enter the relevant SROs from the warranty information table. The option that allows for the drive in/drive out allowance can only be claimed if the vehicle is brought back into the workshop for this action alone to be undertaken. Warranty claims should be submitted in accordance with the current JLR Warranty Manual and its amendments, unless stated otherwise in this bulletin. Customer Reimbursement and Related Damage Process NOTE: If there is a requirement to claim for related/consequential damage or customer reimbursement, refer to the related instruction that can be found in TOPIx (in the Search box search for ‘Related Damage Claim’ and open the related bulletin link). Table of Contents REMOVAL AND INSTALLATION: SERVICE INSTRUCTION 1 – XF VEHICLES REMOVAL AND INSTALLATION: SERVICE INSTRUCTION 2 – XE VEHICLES REMOVAL AND INSTALLATION: SERVICE INSTRUCTION 3 – F-PACE VEHICLES REMOVAL AND INSTALLATION: SERVICE INSTRUCTION 4 – F-TYPE VEHICLES SERVICE INSTRUCTION 1 – XF VEHICLES NOTES: Some illustrations may vary depending on the vehicle specification but the essential information is always correct. Some components are shown removed from the vehicle to provide extra clarity. Front safety belt retractor is also known as front row seatbelt retractor in the TOPIx Workshop Manual. 1. Position the front row seat to the most forward position. 2. Release the 2 door aperture seals. 3. Release, but do not fully remove the b-pillar upper trim panel. 1. Release the 2 lower trim clips. 2. Release the 2 center clips. 4. Remove the b-pillar upper trim panel. 1. Release the b-pillar upper trim panel from the b-pillar. 2. Release the 2 upper locating arms. 5. Remove the front treadplate. 6. Remove the rear treadplate. 7. Remove the b-pillar lower trim panel. Release the 4 trim clips. 8. Repeat steps 1 to 7 for the opposite side of the vehicle. 9. Inspect both front safety belt retractors for damage shown in the area marked ‘A’ in the illustrations. Any front safety belt retractors which are damaged, as shown in the illustration marked with a RED ‘X’, must be renewed. Continue to step 10 to renew any damaged front safety belt retractors. If both front safety belt retractors are not damaged, as shown in the illustration marked with a GREEN ‘✓’, reverse steps 1 to 8 above. 10. Renew the damaged front safety belt retractor(s), (see TOPIx Workshop Manual section 501-20: Seatbelt System – Removal and Installation – Front Safety Belt Retractor). SERVICE INSTRUCTION 2 – XE VEHICLES NOTES: Some illustrations may vary depending on the vehicle specification but the essential information is always correct. Some components are shown removed from the vehicle to provide extra clarity. Front safety belt retractor is also known as front row seatbelt retractor in the TOPIx Workshop Manual. 1. Position the front row seat to the most forward position. 2. Release the 2 door aperture seals. 3. Release, but do not fully remove the b-pillar upper trim panel. 1. Release the 2 lower trim clips. 2. Release the 2 center clips. 4. Remove the b-pillar upper trim panel. 1. Release the b-pillar upper trim panel from the b-pillar. 2. Release the 2 upper locating arms. 5. Remove the front treadplate. 6. Release the second row seat cushion. Release the 2 second row center seatbelt buckles. Release the 4 clips. 7. Remove the rear treadplate. 8. Remove the b-pillar lower trim panel. Release the 4 trim clips. 9. Repeat steps 1 to 8 for the opposite side of the vehicle. 10. Inspect both front safety belt retractors for damage shown in the area marked ‘A’ in the illustrations. Any front safety belt retractors which are damaged, as shown in the illustration marked with a RED ‘X’, must be renewed. Continue to step 11 to renew any damaged front safety belt retractors. If both front safety belt retractors are not damaged, as shown in the illustration marked with a GREEN ‘✓’, reverse steps 1 to 9 above. 11. Renew the damaged front safety belt retractor(s), (see TOPIx Workshop Manual section 501-20: Seatbelt System – Removal and Installation – Front Safety Belt Retractor). SERVICE INSTRUCTION 3 – F-PACE VEHICLES NOTES: Some illustrations may vary depending on the vehicle specification but the essential information is always correct. Some components are shown removed from the vehicle to provide extra clarity. Front safety belt retractor is also known as front row seatbelt retractor in the TOPIx Workshop Manual. 1. Position the front row seat to the most forward position. 2. Release the 2 door aperture seals. 3. Release, but do not fully remove the b-pillar upper trim panel. 1. Release the 2 lower trim clips. 2. Release the 2 center clips. 4. Remove the b-pillar upper trim panel. 1. Release the b-pillar upper trim panel from the b-pillar. 2. Release the 2 upper locating arms. 5. NOTE: Do not disconnect the electrical connector. Release the front treadplate. 6. Release the second row seat cushion. 7. NOTE: Do not disconnect the electrical connector. Release the rear treadplate. 8. Remove the b-pillar lower trim panel. Release the 4 trim clips. 9. Repeat steps 1 to 8 for the opposite side of the vehicle. 10. NOTE: Use a suitable telescopic/flexible mirror to assist with this step. Inspect both front safety belt retractors for damage shown in the area marked ‘A’ in the illustrations. Any front safety belt retractors which are damaged, as shown in the illustration marked with a RED ‘X’, must be renewed. Continue to step 11 to renew any damaged front safety belt retractors. If both front safety belt retractors are not damaged, as shown in the illustration marked with a GREEN ‘✓’, reverse steps 1 to 9 above. 11. Renew the damaged front safety belt retractor(s), (see TOPIx Workshop Manual section 501-20: Seatbelt System – Removal and Installation – Front Safety Belt Retractor). SERVICE INSTRUCTION 4 – F-TYPE VEHICLES NOTES: Some illustrations may vary depending on the vehicle specification but the essential information is always correct. Some components are shown removed from the vehicle to provide extra clarity. Front safety belt retractor is also known as front row seatbelt retractor in the TOPIx Workshop Manual. FIXED ROOF VEHICLES ONLY 1. NOTE: Repeat this step for the opposite side of the vehicle. Position the front row seat to the most forward position. 2. NOTE: Repeat this step for the opposite side of the vehicle. Reposition the front seat backrest for access. 3. NOTE: Repeat this step for the opposite side of the vehicle. Remove the front treadplate. 4. NOTE: Repeat this step for the opposite side of the vehicle. Remove the trim panel. 5. Remove the trim panel. 6. Remove the parcel shelf. 7. NOTE: Repeat this step for the opposite side of the vehicle. Remove the trim panel. 8. Inspect both front safety belt retractors for damage shown in the area marked ‘A’ in the illustrations. Any front safety belt retractors which are damaged, as shown in the illustration marked with a RED ‘X’, must be renewed. Continue to step 9 to renew any damaged front safety belt retractors. If both front safety belt retractors are not damaged, as shown in the illustration marked with a GREEN ‘✓’, reverse steps 1 to 7 above. 9. Renew the damaged front safety belt retractor(s), (see TOPIx Workshop Manual section 501-20: Seatbelt System – Removal and Installation – Front Safety Belt Retractor). FOLDING TOP VEHICLES ONLY 10. Disconnect the startup battery, (see TOPIx Workshop Manual section 414- 01: Battery, Mounting And Cables – General Procedures – Startup Battery Disconnect And Connect) 11. NOTE: Repeat this step for the opposite side of the vehicle. Position the front row seat to the most forward position. 12. NOTE: Repeat this step for the opposite side of the vehicle. Reposition the front seat backrest for access. 13. NOTE: Repeat this step for the opposite side of the vehicle. Remove the front treadplate. 14. NOTE: Repeat this step for the opposite side of the vehicle. Release the trim. 15. Remove the trim panels. 16. NOTE: Repeat this step for the opposite side of the vehicle. Remove the roll-over protection bar. Torque: 45 Nm 17. Remove the trim clips. 18. Remove the parcel shelf. 19. NOTE: Repeat this step for the opposite side of the vehicle. Remove the trim panel. 20. Inspect both front safety belt retractors for damage shown in the area marked ‘A’ in the illustrations. Any front safety belt retractors which are damaged, as shown in the illustration marked with a RED ‘X’, must be renewed. Continue to step 21 to renew any damaged front safety belt retractors. If both front safety belt retractors are not damaged, as shown in the illustration marked with a GREEN ‘✓’, reverse steps 10 to 19 above. 21. Renew the damaged front safety belt retractor(s), (see TOPIx Workshop Manual section 501-20: Seatbelt System – Removal and Installation – Front Safety Belt Retractor). SAMPLE CUSTOMER LETTER – FOR INFORMATION ONLY Name Address line 1 Address line 2 Address line 3 Post Code Vehicle Identification Number (VIN): Registration Number: Program Number: H412 Date: month/year SAFETY RELATED RECALL – F-PACE, F-TYPE, XE and XF vehicles – Autoliv Seatbelt Retractor Functionality Dear Jaguar Land Rover Limited would like to advise you that during ongoing quality assessment of our product it has been identified that a possible safety related problem may occur on certain Jaguar vehicles within a specific production range. Please read the information below, this will explain the actions that we intend to take and what you will need to do. Why are we contacting you? We have identified that the seatbelt pretensioner tube installed on the front seatbelt retractor may have been damaged during the manufacturing process. The damaged tube could prevent the pretensioner from correctly operating by not pre-tensioning the seatbelt in the event of an accident, where it would normally operate. This may result in a reduction or complete loss of pre-tensioning in the event of a crash and increased occupant injury. What will your Jaguar retailer/authorized repairer do? We will inspect the seatbelt pretensioner tube for damage and renew the seatbelt retractor if required. How long will it take? The work on your vehicle will be completed as quickly and efficiently as possible in order to minimize inconvenience to you. Your retailer/authorized repairer will be able to advise how long your vehicle will be required for when a booking is made. What we are asking you to do Please contact your preferred Jaguar retailer/authorized repairer without delay. To book your vehicle in for this action you will need to provide the retailer/authorized repairer with the following which are detailed at the beginning of this letter: • The VIN for your vehicle • Vehicle registration number of your vehicle. • The program code for the action. If you do not have a retailer/authorized repairer, please access or www.jaguar.com for contact details. If you no longer own the vehicle could you please complete the ‘Change of Ownership’ slip attached to this letter, returning the slip to Jaguar Land Rover Limited immediately in the enclosed ‘Freepost’ envelope. This will enable us to make contact with the new owner. If you have concerns If you experience any concerns relating to this Recall, contact the Service Manager at the retailer/authorized repairer for assistance or contact the JLR Limited Customer Experience Centre on 0345 303 2303 or (enter phone number). This bulletin is being issued in accordance with the legislative or industry requirements concerning vehicle defects. The authorities will closely monitor the response rate of this bulletin. Please treat this matter with the urgency it requires, JLR Limited apologize for any inconvenience this bulletin may cause and thank you, in advance, for your co-operation. Yours sincerely Head of Business Technical Questions And Answers FOR USE ON ENQUIRY Jaguar Land Rover H412 2022 model year F-TYPE, XE and XF vehicles and 2022 and 2023 model year F-PACE vehicles Seatbelt Pretensioner Functionality A concern has been identified on certain 2022 model year F-TYPE, XE and XF vehicles and certain 2022 and 2023 model year FPACE vehicles where, due to a retailer production issue, a damaged front seatbelt pretensioner tube may have been installed on the seatbelt retractor. The damaged tube could prevent the pretensioner from operating correctly in the event of an accident. Question 1 Why is Jaguar Land Rover (JLR) Limited recalling these vehicles? Answer JLR is conducting a voluntary safety recall involving certain 2022 model year F-TYPE, XE and XF vehicles and certain 2022 and 2023 model year F-PACE vehicles. Customers will be asked to take their vehicles to an approved retailer/authorized repairer to have the seatbelt pretensioner tube inspected for damage and if damage is identified, the seatbelt retractor will be renewed. Question 2 Can you tell me more about what is wrong with the vehicles? Answer Autoliv (seatbelt retailer) made JLR aware of a manufacturing concern detected on some front seatbelt retractors that results in damage to the pretensioner tube caused during seatbelt retractor assembly. This may result in a reduced level or complete loss of pre-tensioning in the event of a crash and increased occupant injury. Question 3 How would the customer become aware of their vehicle potentially having this concern? Answer This concern may manifest itself only in the event of a crash where a seatbelt pretensioner would normally operate. Question 4 Does this concern affect vehicle safety? Answer JLR has determined that the seatbelt pretensioner not operating correctly could pose a risk to vehicle safety in the event of an accident. Question 5 Has JLR received many complaints? Answer JLR has received no field reports of vehicles that could be attributed to this issue. Question 6 Have there been any accidents or injuries or fires? Answer There have been no reports of accidents or injuries or fires relating to this concern of which JLR is aware. Question 7 How was the concern discovered? Answer JLR were notified of this concern by the seatbelt manufacturer, Autoliv. Question 8 How long has JLR known about this concern? Answer JLR were notified of this concern on April 8, 2022. Question 9 Is the defect leading you to any concerns regarding the reliability of a system, which is supposed to be designed and engineered for the passengers’ safety? What type of measures are you planning to take? Answer JLR has no concerns with the overall reliability of the vehicle. JLR carefully monitors field data to make sure that any matters relating to safety and compliance are rigorously investigated. Question 10 What has JLR done in production? Answer This is a JLR retailer issue which has been addressed in the retailer manufacturing process by introducing sensors to detect mispositioning of the retractor and stop the manufacturing process where mis-positioning is detected. Question 11 What will retailers/authorized repairers do to the vehicles? Answer Retailers/authorized repairers will inspect the front seatbelt pretensioner tubes for damage and if damage is identified, the seatbelt retractor will be replaced. Question 12 Which vehicles are affected by this recall? • Answer Certain 2022 and 2023 model year Jaguar vehicles within the Vehicle Identification Number (VIN) ranges are potentially affected: • F-PACE from SADCJ2EX2NA693574 to SADCA2BW5NA695394 (Solihull Manufacturing Plant) • F-TYPE from SAJDB1BX5NCK78735 to SAJDA1AE4NCK79393 (Castle Bromwich Manufacturing Plant) • XE from SAJAA4BN1NCP69339 to SAJAB4BNXNCP69420 (Castle Bromwich Manufacturing Plant) • XF from SAJBL4GX1NCY91515 to SAJBL4GX5NCY91713 (Castle Bromwich Manufacturing Plant) Question 13 Are other JLR models affected by this concern? Answer Yes, certain 2022 and 2023 Model Year Land Rover Defender, Discovery, Discovery Sport, Range Rover Sport and Range Rover Velar vehicles have also been affected. Question 14 Is the repair available to rework vehicles? Answer Parts are available for JLR retailers/authorized repairers to conduct this repair. Question 15 How much will the recall cost JLR? Answer Cost was not a factor in deciding to recall these vehicles. Question 16 How do I know if my vehicle is affected? Answer All owners of potentially affected vehicles will shortly receive a letter inviting them to contact a JLR retailer/authorized repairer for the work to be completed. Question 17 How long does it take for the vehicle to be inspected and repaired? Answer The work will be completed as quickly and efficiently as possible in order to minimize inconvenience to customers and is expected to take no longer than 1 hour to complete. Naturally, due to retailer/authorized repairer schedules, vehicles may be required for longer. Question 18 Can I safely continue to drive my vehicle until it has been repaired? Answer Customers are advised to contact a JLR retailers/authorized repairers should they have any concerns regarding the seatbelt operation. Note: Please make sure that any press enquiries are referred to the JLR Corporate Affairs office.
**************************************************************************************************************
IMPORTANT SAFETY RECALL This notice applies to your vehicle, September 15, 2022 SAFETY RECALL H412: Damaged Seatbelt Pretensioners Vehicles Affected: Jaguar F-PACE, F-TYPE, XF Model Year: 2022 National Highway Traffic Safety Administration (NHTSA) Recall Number: 22V-524 Dear Jaguar Owner: This notice is sent to you in accordance with the National Traffic and Motor Vehicle Safety Act. Jaguar has decided that a defect which relates to motor vehicle safety exists in certain 2022 model year Jaguar F-PACE, F-TYPE and XF vehicles. Your vehicle is included in this Recall action. What is the reason for this program? Damaged driver and front passenger seat belt pretensioners tube may have been installed. Damaged driver and front passenger seat belt pretensioners could prevent the pretensioner from restraining occupants correctly, which may increase the risk of injury during a crash. What will Jaguar and your authorized Jaguar Retailer do? Jaguar is carrying out a recall of the vehicles mentioned above. An authorized Jaguar retailer will inspect and replace the seat belt pretensioners, as necessary. There will be no charge to owners for this action under this Program. What should you do? Please contact your preferred authorized Jaguar retailer and provide them with your Vehicle Identification Number (VIN) and request a service date to complete the work required under Program Code ‘H412’. Attention Leasing Agencies: If you are a vehicle lessor, Federal Regulations require you to forward this notice to your lessee within ten (10) days. How long will it take? The work will be carried out as quickly and efficiently as possible in order to minimize inconvenience to customers and is expected to take approximately one (1) hour, although your retailer may need your vehicle for a longer time. Your retailer can provide you with a better estimate of the overall time for the service visit. What if I have previously paid for this concern? If you have already paid for this concern before the date of this letter, Jaguar is offering a refund. To qualify for a refund, please provide your authorized Jaguar retailer with the original paid receipt. To avoid delays, please do not send the receipt to Jaguar Land Rover North America. Jaguar Land Rover North America, LLC 100 Jaguar Land Rover Way, Mahwah, NJ 07495 Tel: 201.818.8500 0000075 0000001 Moved or no longer own this Jaguar vehicle? If you are no longer the owner of this vehicle, Jaguar would appreciate the name and address of the new owner (if known); please fill out and return the enclosed return postage-paid card. What should you do if you have further questions? If you have any questions or concerns, please contact the Service Manager at your authorized Jaguar retailer for assistance. If you have any queries or concerns that your retailer cannot address, please contact the Jaguar Customer Relationship Center at 1-800-4JAGUAR (1800-452-4877) and one of our representatives will be happy to assist you. You may also contact us by email using the following address: jagweb1@jaguarlandrover.com. Please include your full name, address, and VIN of your vehicle in your email. If you have the need to contact Jaguar by mail, please use the following address: Jaguar Land Rover North America, LLC ATTN: Customer Relationship Center 100 Jaguar Land Rover Way Mahwah, NJ 07495 If after having attempted to take advantage of this recall you believe you have not been able to have your vehicle remedied without charge and within a reasonable amount of time, you may submit a complaint to the: Administrator National Highway Traffic Safety Administration 1200 New Jersey Ave., S.E., Washington, D.C., 20590 or call the toll-free Vehicle Safety Hotline at 1-888-327-4236 (TTY: 1-800-424-9153); or go to http://www.safercar.gov. Jaguar appreciates your confidence in our product and wish to do everything we can to retain that confidence. We recognize this service visit may be an inconvenience to you. Jaguar, in cooperation with your authorized Jaguar retailer, will strive to minimize any inconvenience to you caused by this program. Sincerely, Thomas Giese Director, Technical Services – MA-43 Customer Service
**************************************************************************************************************
NOTIFICATION OF SAFETY RECALL H412 NAS22.08.003 RECALL USA AFTERSALES BULLETIN August 4, 2022 TO: All authorized Jaguar Retailers RE: Damage of Front Seat Belt Pretensioner Tubes Jaguar Land Rover North America, LLC has informed the National Highway Traffic Safety Administration (NHTSA) of its intent to perform a Safety Recall on certain 2022 model year Jaguar F-TYPE, XF, and F-PACE vehicles imported into the United States market. Information relating to this Recall will be posted on the National Highway Traffic Safety Administration website. United States Federal regulations require that retailers must be notified within a reasonable time after the manufacturer decides that a defect that relates to motor vehicle safety or a noncompliance exists. United States Federal law requires retailers to complete any outstanding Recall service before a new vehicle is delivered to the buyer or lessee. Violation of this requirement by a retailer could result in a civil penalty of up to $24,423.00 per violation and equivalent of $122,106,996.00 for a related series of violations. This Aftersales Bulletin serves as notification to all Jaguar retailers in the United States and Federalized Territories that any affected new vehicles may not be sold and delivered for customer use until the Recall repair is completed. DESCRIPTION OF DEFECT A concern has been identified on certain 2022MY Jaguar F-TYPE, XF, and F-PACE vehicles where a damaged front seat belt pretensioner tube may have been installed on the seat belt retractor. AFFECTED VEHICLE RANGE F-TYPE Model Year: ………………….. 2022 VIN: ………………………………… SAJDD1EE9NCK78757 – SAJD85EE3NCK79169 XF Model Year: ………………….. 2022 VIN: ………………………………… SAJB4GX1NC91515 – SAJBL4GX5NCY91713 F-PACE Model Year: ………………….. 2022 VIN: ………………………………… SADCJEX2NA693574 – SADCZ2EE0NA694892 A total of approximately 176 vehicles in the United States and Federalized Territories. EFFECT OF VEHICLE OPERATION A damaged front seat belt pretensioner tube could prevent the pretensioner from correctly operating by not pre-tensioning the seat belt in the event of an accident where it would normally operate. This may result in a reduced level or complete loss of pre-tensioning in the event of a crash and increased occupant injury. SERVICE PROGRAM/REWORK ACTION Owners will be notified by mail and instructed to take their vehicle to an authorized retailer who will inspect the seat belt pretensioner tube for damage. If damage is identified, the seat belt retractor will be replaced. There will be no charge to the owners for this action under this program. OWNER NOTIFICATION Owner notification is expected to occur on or before the week of September 16, 2022. ACTION TO BE TAKEN Check the Jaguar Land Rover Warranty Portal to make sure affected vehicles are correctly identified prior to starting this campaign. The Warranty Portal will be updated to reflect only those vehicles affected. Retailers/authorized repairers are required to Quarantine affected new vehicles that are within your control and refrain from releasing the vehicles for new vehicle sale pending completion of the rework action. Affected vehicles already with customers should be updated at the next available opportunity. JLR North America recommends that affected sales demonstrator and loaner vehicles are repaired before use and that used vehicles are repaired before sale. Retailers/authorized repairers who choose to proceed against this recommendation, where legally permitted, must clearly and conspicuously disclose the open recall to the applicable customers. A Safety Recall will be published when repair instructions are finalized, and any required parts have been procured. Retailers/authorized repairers are reminded that they must not sell vehicles identified as affected by this campaign until such time as the repair has been successfully completed. After the Safety Recall is launched, visit the British Brands Sales Suite (BBSS) website for a list of affected vehicles at your retailer/authorized repairer.
**************************************************************************************************************
OMB Control No.: 2127-0004 Part 573 Safety Recall Report 22V-524 The information contained in this report was submitted pursuant to 49 CFR §573 Manufacturer Name : Jaguar Land Rover North America, LLC Submission Date : JUL 22, 2022 NHTSA Recall No. : 22V-524 Manufacturer Recall No. : H412 Manufacturer Information : Manufacturer Name : Jaguar Land Rover North America, LLC Address : 100 Jaguar Land Rover Way Mahwah NJ 07495 Company phone : 8188500 Population : Number of potentially involved : 176 Estimated percentage with defect : 100 % Vehicle Information : Vehicle 1 : 2022-2022 JAGUAR F-TYPE Vehicle Type : LIGHT VEHICLES Body Style : 2-DOOR Power Train : NR Descriptive Information : Jaguar Land Rover are conducting a voluntary safety recall campaign involving certain 2022 Model Year Jaguar F-TYPE vehicles built at the Castle Bromwich & Solihull Vehicle Assembly Plants from 17th January 2022 – 8th March 2022. Approximately 9 vehicles in the United States and Federalized Territories. The basis of the recall population was derived from the production periods seatbelts provided could have been incorrectly manufactured by Autoliv and installed into vehicles. Production Dates : JAN 17, 2022 – MAR 08, 2022 VIN Range 1 : Begin : SAJDD1EE9NCK78757 End : SAJD85EE3NCK79169 Not sequential Vehicle 2 : 2022-2022 JAGUAR F-PACE Vehicle Type : LIGHT VEHICLES Body Style : SUV Power Train : NR Descriptive Information : Jaguar Land Rover are conducting a voluntary safety recall campaign involving certain 2022 Model Year Jaguar F-PACE vehicles built at the Castle Bromwich & Solihull Vehicle Assembly Plants from 17th January 2022 – 8th March 2022. Approximately 112 vehicles in the United States and Federalized Territories. The basis of the recall population was derived from the production periods seatbelts provided could have been incorrectly manufactured by Autoliv and installed into vehicles. Production Dates : JAN 17, 2022 – MAR 08, 2022 VIN Range 1 : Begin : SADCJ2EX2NA693574 End : SADCZ2EE0NA694892 Not sequential Part 573 Safety Recall Report 22V-524 Page 2 The information contained in this report was submitted pursuant to 49 CFR §573 Vehicle 3 : 2022-2022 JAGUAR XF Vehicle Type : LIGHT VEHICLES Body Style : 4-DOOR Power Train : NR Descriptive Information : Jaguar Land Rover are conducting a voluntary safety recall campaign involving certain 2022 Model Year Jaguar XF vehicles built at the Castle Bromwich & Solihull Vehicle Assembly Plants from 17th January 2022 – 8th March 2022. Approximately 55 vehicles in the United States and Federalized Territories. The basis of the recall population was derived from the production periods seatbelts provided could have been incorrectly manufactured by Autoliv and installed into vehicles. Production Dates : JAN 17, 2022 – MAR 08, 2022 VIN Range 1 : Begin : SAJBL4GX1NCY91515 End : SAJBL4GX5NCY91713 Not sequential Description of Defect : Description of the Defect : A concern has been identified on certain 2022 Model Year Jaguar F-TYPE, FPACE & XF vehicles where a damaged front seat belt pretensioner tube may have been installed on the seat belt retractor. FMVSS 1 : NR FMVSS 2 : NR Description of the Safety Risk : A damaged front seat belt pretensioner tube could prevent the pretensioner from correctly operating by not pre-tensioning the seat belt in the event of an accident where it would normally operate. This may result in a reduced level or complete loss of pre-tensioning in the event of a crash and increased occupant injury. Description of the Cause : NR Identification of Any Warning that can Occur : NR Involved Components : Component Name 1 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B08-AC8AAM Part 573 Safety Recall Report 22V-524 Page 3 The information contained in this report was submitted pursuant to 49 CFR §573 Component Name 2 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B09-AC8AAM Component Name 3 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B08-AC8PVJ Component Name 4 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B08-LD8AAM Component Name 5 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B08-LD8PVJ Component Name 6 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B09-AC8PVJ Component Name 7 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B09-ED8AAM Component Name 8 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B09-ED8PVJ Part 573 Safety Recall Report 22V-524 Page 4 The information contained in this report was submitted pursuant to 49 CFR §573 Component Name 9 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : FK72-611B09-AE8PVJ Component Name 10 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : GX63-611B08-AF8PVJ Component Name 11 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : GX63-611B09-BF8PVJ Component Name 12 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : GX73-611B08-AE8PVJ Component Name 13 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : GX73-611B09-CD8PVJ Component Name 14 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : HK83-611B09-AD8PVJ Component Name 15 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : HK83-611B09-BD8PVJ Part 573 Safety Recall Report 22V-524 Page 5 The information contained in this report was submitted pursuant to 49 CFR §573 Component Name 16 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : HY32-611B08-AD8PVJ Component Name 17 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : HY32-611B08-CD8PVJ Component Name 18 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : HY32-611B09-AD8PVJ Component Name 19 : Seat Belt Assembly Component Description : Seat Belt Assemblyv Component Part Number : HY32-611B09-DA8PVJ Component Name 20 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : JX53-611B08-BB0CJA Component Name 21 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : JX53-611B08-BB0PVJ Component Name 22 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : JX53-611B09-AC0CJA Part 573 Safety Recall Report 22V-524 Page 6 The information contained in this report was submitted pursuant to 49 CFR §573 Component Name 23 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : JX53-611B09-BB0PVJ Component Name 24 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : L8B2-6110B08-AB8PVJ Component Name 25 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : L8B2-6110B08-CB8PVJ Component Name 26 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : L8B2-6110B08-EB8PVJ Component Name 27 : Seat Belt Assembly, Seat Belt Assembly Component Description : Seat Belt Assembly, Seat Belt Assembly Component Part Number : L8B2-6110B09-AB8PVJ, HK83-611B08-AD8PVJ Component Name 28 : Seat Belt Assembly, Seat Belt Assembly Component Description : Seat Belt Assembly, Seat Belt Assembly Component Part Number : L8B2-6110B09-DB8PVJ, L8B2-611B09-BB8PVJ Component Name 29 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : LK72-611B08-AB8PVJ Part 573 Safety Recall Report 22V-524 Page 7 The information contained in this report was submitted pursuant to 49 CFR §573 Supplier Identification : Component Manufacturer Name : AUTOLIV B.V. & CO. KG Address : NR SOPRONKOVESD Foreign States 9483 Country : Hungary Chronology : Following a notification from Autoliv that a defect had been identified during their manufacturing process that caused damage to a small number of front seat belt pretentioner tubes, Jaguar Land Rover (JLR) opened a PSCC (Product Safety & Compliance Committee) investigation on May 25, 2022. The PSCC requested that Vehicle Assembly Plants conduct an exercise to identify if they had received any parts from the batches Autoliv deemed at risk and the population of affected vehicles that may have received parts from these batches. On June 1, 2022, Autoliv presented the issue to the PSCC, Autoliv explained the issue that had been identified on one of their seatbelt production lines and the potential impact on the component functionality. During June, each vehicle assembly plant conducted detailed research to identify which batches deemed at risk by Autoliv had been consumed and the specific vehicle identification numbers of vehicles that may have received parts from these batches. In July, the qualification/identification of damaged parts was confirmed, and the subject matter experts within JLR confirmed the impact of damaged pretentioners on the Supplementary Restraints System (SRS) and on occupant protection. At the PSCC of July 13, 2022, the scope was discussed along with exposure and vehicle disposition confirmed. Based on the feedback provided, the PSCC progressed the issue to the Recall Determination Committee (RDC) for review. The RDC reviewed the issue on July 14, 2022, and concluded that it represented an unreasonable risk to safety and a voluntary safety recall should be conducted to inspect the pretensioner on all vehicles identified to be at risk of receiving a damaged pretensioner, and if a damaged component is identified, the seatbelt assembly should be replaced. Description of Remedy : Description of Remedy Program : Owners will be notified and instructed to take their vehicle to an approved Jaguar Land Rover repairer. The technician will inspect the seat belt pretensioner tube for damage and if damage is identified, the seat belt retractor will be replaced. There will be no charge to the owners for this repair. The affected vehicles will be covered under Jaguar’s new vehicle warranty program. Therefore, reimbursement for pre-notice remedies are not necessary because the affected vehicles are still under warranty. How Remedy Component Differs from Recalled Component : NR Identify How/When Recall Condition was Corrected in Production : NR Part 573 Safety Recall Report 22V-524 Page 8 The information contained in this report was submitted pursuant to 49 CFR §573 Recall Schedule : Description of Recall Schedule : Distribution of owner notification letters will occur on or before September 16, 2022. Notifications to dealers will occur on August 4, 2022. Planned Dealer Notification Date : AUG 04, 2022 – AUG 04, 2022 Planned Owner Notification Date : SEP 16, 2022 – SEP 16, 2022 * NR – Not Reported
**************************************************************************************************************
OMB Control No.: 2127-0004 Part 573 Safety Recall Report 22V-524 The information contained in this report was submitted pursuant to 49 CFR §573 Manufacturer Name : Jaguar Land Rover North America, LLC Submission Date : AUG 03, 2022 NHTSA Recall No. : 22V-524 Manufacturer Recall No. : H412 Manufacturer Information : Manufacturer Name : Jaguar Land Rover North America, LLC Address : 100 Jaguar Land Rover Way Mahwah NJ 07495 Company phone : 8188500 Population : Number of potentially involved : 176 Estimated percentage with defect : 100 % Vehicle Information : Vehicle 1 : 2022-2022 JAGUAR F-TYPE Vehicle Type : LIGHT VEHICLES Body Style : 2-DOOR Power Train : NR Descriptive Information : Jaguar Land Rover are conducting a voluntary safety recall campaign involving certain 2022 Model Year Jaguar F-TYPE vehicles built at the Castle Bromwich & Solihull Vehicle Assembly Plants from 17th January 2022 – 8th March 2022. Approximately 9 vehicles in the United States and Federalized Territories. The basis of the recall population was derived from the production periods seatbelts provided could have been incorrectly manufactured by Autoliv and installed into vehicles. Production Dates : JAN 17, 2022 – MAR 08, 2022 VIN Range 1 : Begin : SAJDD1EE9NCK78757 End : SAJD85EE3NCK79169 Not sequential Vehicle 2 : 2022-2022 JAGUAR XF Vehicle Type : LIGHT VEHICLES Body Style : 4-DOOR Power Train : NR Descriptive Information : Jaguar Land Rover are conducting a voluntary safety recall campaign involving certain 2022 Model Year Jaguar XF vehicles built at the Castle Bromwich & Solihull Vehicle Assembly Plants from 17th January 2022 – 8th March 2022. Approximately 55 vehicles in the United States and Federalized Territories. The basis of the recall population was derived from the production periods seatbelts provided could have been incorrectly manufactured by Autoliv and installed into vehicles. Production Dates : JAN 17, 2022 – MAR 08, 2022 VIN Range 1 : Begin : SAJBL4GX1NCY91515 End : SAJBL4GX5NCY91713 Not sequential Part 573 Safety Recall Report 22V-524 Page 2 The information contained in this report was submitted pursuant to 49 CFR §573 Vehicle 3 : 2022-2022 JAGUAR F-PACE Vehicle Type : LIGHT VEHICLES Body Style : SUV Power Train : NR Descriptive Information : Jaguar Land Rover are conducting a voluntary safety recall campaign involving certain 2022 Model Year Jaguar F-PACE vehicles built at the Castle Bromwich & Solihull Vehicle Assembly Plants from 17th January 2022 – 8th March 2022. Approximately 112 vehicles in the United States and Federalized Territories. The basis of the recall population was derived from the production periods seatbelts provided could have been incorrectly manufactured by Autoliv and installed into vehicles. Production Dates : JAN 17, 2022 – MAR 08, 2022 VIN Range 1 : Begin : SADCJ2EX2NA693574 End : SADCZ2EE0NA694892 Not sequential Description of Defect : Description of the Defect : A concern has been identified on certain 2022 Model Year Jaguar F-TYPE, FPACE & XF vehicles where a damaged front seat belt pretensioner tube may have been installed on the seat belt retractor. FMVSS 1 : NR FMVSS 2 : NR Description of the Safety Risk : A damaged front seat belt pretensioner tube could prevent the pretensioner from correctly operating by not pre-tensioning the seat belt in the event of an accident where it would normally operate. This may result in a reduced level or complete loss of pre-tensioning in the event of a crash and increased occupant injury. Description of the Cause : NR Identification of Any Warning that can Occur : NR Involved Components : Component Name 1 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B08-AC8AAM Part 573 Safety Recall Report 22V-524 Page 3 The information contained in this report was submitted pursuant to 49 CFR §573 Component Name 2 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B09-AC8AAM Component Name 3 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B08-AC8PVJ Component Name 4 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B08-LD8AAM Component Name 5 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B08-LD8PVJ Component Name 6 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B09-AC8PVJ Component Name 7 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B09-ED8AAM Component Name 8 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B09-ED8PVJ Part 573 Safety Recall Report 22V-524 Page 4 The information contained in this report was submitted pursuant to 49 CFR §573 Component Name 9 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : FK72-611B09-AE8PVJ Component Name 10 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : GX63-611B08-AF8PVJ Component Name 11 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : GX63-611B09-BF8PVJ Component Name 12 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : GX73-611B08-AE8PVJ Component Name 13 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : GX73-611B09-CD8PVJ Component Name 14 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : HK83-611B09-AD8PVJ Component Name 15 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : HK83-611B09-BD8PVJ Part 573 Safety Recall Report 22V-524 Page 5 The information contained in this report was submitted pursuant to 49 CFR §573 Component Name 16 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : HY32-611B08-AD8PVJ Component Name 17 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : HY32-611B08-CD8PVJ Component Name 18 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : HY32-611B09-AD8PVJ Component Name 19 : Seat Belt Assembly Component Description : Seat Belt Assemblyv Component Part Number : HY32-611B09-DA8PVJ Component Name 20 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : JX53-611B08-BB0CJA Component Name 21 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : JX53-611B08-BB0PVJ Component Name 22 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : JX53-611B09-AC0CJA Part 573 Safety Recall Report 22V-524 Page 6 The information contained in this report was submitted pursuant to 49 CFR §573 Component Name 23 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : JX53-611B09-BB0PVJ Component Name 24 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : L8B2-6110B08-AB8PVJ Component Name 25 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : L8B2-6110B08-CB8PVJ Component Name 26 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : L8B2-6110B08-EB8PVJ Component Name 27 : Seat Belt Assembly, Seat Belt Assembly Component Description : Seat Belt Assembly, Seat Belt Assembly Component Part Number : L8B2-6110B09-AB8PVJ, HK83-611B08-AD8PVJ Component Name 28 : Seat Belt Assembly, Seat Belt Assembly Component Description : Seat Belt Assembly, Seat Belt Assembly Component Part Number : L8B2-6110B09-DB8PVJ, L8B2-611B09-BB8PVJ Component Name 29 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : LK72-611B08-AB8PVJ Part 573 Safety Recall Report 22V-524 Page 7 The information contained in this report was submitted pursuant to 49 CFR §573 Supplier Identification : Component Manufacturer Name : AUTOLIV B.V. & CO. KG Address : NR SOPRONKOVESD Foreign States 9483 Country : Hungary Chronology : Following a notification from Autoliv that a defect had been identified during their manufacturing process that caused damage to a small number of front seat belt pretentioner tubes, Jaguar Land Rover (JLR) opened a PSCC (Product Safety & Compliance Committee) investigation on May 25, 2022. The PSCC requested that Vehicle Assembly Plants conduct an exercise to identify if they had received any parts from the batches Autoliv deemed at risk and the population of affected vehicles that may have received parts from these batches. On June 1, 2022, Autoliv presented the issue to the PSCC, Autoliv explained the issue that had been identified on one of their seatbelt production lines and the potential impact on the component functionality. During June, each vehicle assembly plant conducted detailed research to identify which batches deemed at risk by Autoliv had been consumed and the specific vehicle identification numbers of vehicles that may have received parts from these batches. In July, the qualification/identification of damaged parts was confirmed, and the subject matter experts within JLR confirmed the impact of damaged pretentioners on the Supplementary Restraints System (SRS) and on occupant protection. At the PSCC of July 13, 2022, the scope was discussed along with exposure and vehicle disposition confirmed. Based on the feedback provided, the PSCC progressed the issue to the Recall Determination Committee (RDC) for review. The RDC reviewed the issue on July 14, 2022, and concluded that it represented an unreasonable risk to safety and a voluntary safety recall should be conducted to inspect the pretensioner on all vehicles identified to be at risk of receiving a damaged pretensioner, and if a damaged component is identified, the seatbelt assembly should be replaced. There are no warranty claims, field or service reports, or other information (such as the numbers of deaths and/or injuries), associated with this recall. Description of Remedy : Description of Remedy Program : Owners will be notified and instructed to take their vehicle to an approved Jaguar Land Rover repairer. The technician will inspect the seat belt pretensioner tube for damage and if damage is identified, the seat belt retractor will be replaced. There will be no charge to the owners for this repair. The affected vehicles will be covered under Jaguar’s new vehicle warranty program. Therefore, reimbursement for pre-notice remedies are not necessary because the affected vehicles are still under warranty. How Remedy Component Differs from Recalled Component : NR Part 573 Safety Recall Report 22V-524 Page 8 The information contained in this report was submitted pursuant to 49 CFR §573 Identify How/When Recall Condition was Corrected in Production : NR Recall Schedule : Description of Recall Schedule : Distribution of owner notification letters will occur on or before September 16, 2022. Notifications to dealers will occur on August 4, 2022. Planned Dealer Notification Date : AUG 04, 2022 – AUG 04, 2022 Planned Owner Notification Date : SEP 16, 2022 – SEP 16, 2022 * NR – Not Reported
**************************************************************************************************************
OMB Control No.: 2127-0004 Part 573 Safety Recall Report 22V-524 The information contained in this report was submitted pursuant to 49 CFR §573 Manufacturer Name : Jaguar Land Rover North America, LLC Submission Date : JUL 22, 2022 NHTSA Recall No. : 22V-524 Manufacturer Recall No. : H412 Manufacturer Information : Manufacturer Name : Jaguar Land Rover North America, LLC Address : 100 Jaguar Land Rover Way Mahwah NJ 07495 Company phone : 8188500 Population : Number of potentially involved : 176 Estimated percentage with defect : 100 % Vehicle Information : Vehicle 1 : 2022-2022 JAGUAR F-TYPE Vehicle Type : LIGHT VEHICLES Body Style : 2-DOOR Power Train : NR Descriptive Information : Jaguar Land Rover are conducting a voluntary safety recall campaign involving certain 2022 Model Year Jaguar F-TYPE vehicles built at the Castle Bromwich & Solihull Vehicle Assembly Plants from 17th January 2022 – 8th March 2022. Approximately 9 vehicles in the United States and Federalized Territories. The basis of the recall population was derived from the production periods seatbelts provided could have been incorrectly manufactured by Autoliv and installed into vehicles. Production Dates : JAN 17, 2022 – MAR 08, 2022 VIN Range 1 : Begin : SAJDD1EE9NCK78757 End : SAJD85EE3NCK79169 Not sequential Vehicle 2 : 2022-2022 JAGUAR F-PACE Vehicle Type : LIGHT VEHICLES Body Style : SUV Power Train : NR Descriptive Information : Jaguar Land Rover are conducting a voluntary safety recall campaign involving certain 2022 Model Year Jaguar F-PACE vehicles built at the Castle Bromwich & Solihull Vehicle Assembly Plants from 17th January 2022 – 8th March 2022. Approximately 112 vehicles in the United States and Federalized Territories. The basis of the recall population was derived from the production periods seatbelts provided could have been incorrectly manufactured by Autoliv and installed into vehicles. Production Dates : JAN 17, 2022 – MAR 08, 2022 VIN Range 1 : Begin : SADCJ2EX2NA693574 End : SADCZ2EE0NA694892 Not sequential Part 573 Safety Recall Report 22V-524 Page 2 The information contained in this report was submitted pursuant to 49 CFR §573 Vehicle 3 : 2022-2022 JAGUAR XF Vehicle Type : LIGHT VEHICLES Body Style : 4-DOOR Power Train : NR Descriptive Information : Jaguar Land Rover are conducting a voluntary safety recall campaign involving certain 2022 Model Year Jaguar XF vehicles built at the Castle Bromwich & Solihull Vehicle Assembly Plants from 17th January 2022 – 8th March 2022. Approximately 55 vehicles in the United States and Federalized Territories. The basis of the recall population was derived from the production periods seatbelts provided could have been incorrectly manufactured by Autoliv and installed into vehicles. Production Dates : JAN 17, 2022 – MAR 08, 2022 VIN Range 1 : Begin : SAJBL4GX1NCY91515 End : SAJBL4GX5NCY91713 Not sequential Description of Defect : Description of the Defect : A concern has been identified on certain 2022 Model Year Jaguar F-TYPE, FPACE & XF vehicles where a damaged front seat belt pretensioner tube may have been installed on the seat belt retractor. FMVSS 1 : NR FMVSS 2 : NR Description of the Safety Risk : A damaged front seat belt pretensioner tube could prevent the pretensioner from correctly operating by not pre-tensioning the seat belt in the event of an accident where it would normally operate. This may result in a reduced level or complete loss of pre-tensioning in the event of a crash and increased occupant injury. Description of the Cause : NR Identification of Any Warning that can Occur : NR Involved Components : Component Name 1 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B08-AC8AAM Part 573 Safety Recall Report 22V-524 Page 3 The information contained in this report was submitted pursuant to 49 CFR §573 Component Name 2 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B09-AC8AAM Component Name 3 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B08-AC8PVJ Component Name 4 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B08-LD8AAM Component Name 5 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B08-LD8PVJ Component Name 6 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B09-AC8PVJ Component Name 7 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B09-ED8AAM Component Name 8 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B09-ED8PVJ Part 573 Safety Recall Report 22V-524 Page 4 The information contained in this report was submitted pursuant to 49 CFR §573 Component Name 9 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : FK72-611B09-AE8PVJ Component Name 10 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : GX63-611B08-AF8PVJ Component Name 11 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : GX63-611B09-BF8PVJ Component Name 12 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : GX73-611B08-AE8PVJ Component Name 13 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : GX73-611B09-CD8PVJ Component Name 14 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : HK83-611B09-AD8PVJ Component Name 15 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : HK83-611B09-BD8PVJ Part 573 Safety Recall Report 22V-524 Page 5 The information contained in this report was submitted pursuant to 49 CFR §573 Component Name 16 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : HY32-611B08-AD8PVJ Component Name 17 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : HY32-611B08-CD8PVJ Component Name 18 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : HY32-611B09-AD8PVJ Component Name 19 : Seat Belt Assembly Component Description : Seat Belt Assemblyv Component Part Number : HY32-611B09-DA8PVJ Component Name 20 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : JX53-611B08-BB0CJA Component Name 21 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : JX53-611B08-BB0PVJ Component Name 22 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : JX53-611B09-AC0CJA Part 573 Safety Recall Report 22V-524 Page 6 The information contained in this report was submitted pursuant to 49 CFR §573 Component Name 23 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : JX53-611B09-BB0PVJ Component Name 24 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : L8B2-6110B08-AB8PVJ Component Name 25 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : L8B2-6110B08-CB8PVJ Component Name 26 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : L8B2-6110B08-EB8PVJ Component Name 27 : Seat Belt Assembly, Seat Belt Assembly Component Description : Seat Belt Assembly, Seat Belt Assembly Component Part Number : L8B2-6110B09-AB8PVJ, HK83-611B08-AD8PVJ Component Name 28 : Seat Belt Assembly, Seat Belt Assembly Component Description : Seat Belt Assembly, Seat Belt Assembly Component Part Number : L8B2-6110B09-DB8PVJ, L8B2-611B09-BB8PVJ Component Name 29 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : LK72-611B08-AB8PVJ Part 573 Safety Recall Report 22V-524 Page 7 The information contained in this report was submitted pursuant to 49 CFR §573 Supplier Identification : Component Manufacturer Name : AUTOLIV B.V. & CO. KG Address : NR SOPRONKOVESD Foreign States 9483 Country : Hungary Chronology : Following a notification from Autoliv that a defect had been identified during their manufacturing process that caused damage to a small number of front seat belt pretentioner tubes, Jaguar Land Rover (JLR) opened a PSCC (Product Safety & Compliance Committee) investigation on May 25, 2022. The PSCC requested that Vehicle Assembly Plants conduct an exercise to identify if they had received any parts from the batches Autoliv deemed at risk and the population of affected vehicles that may have received parts from these batches. On June 1, 2022, Autoliv presented the issue to the PSCC, Autoliv explained the issue that had been identified on one of their seatbelt production lines and the potential impact on the component functionality. During June, each vehicle assembly plant conducted detailed research to identify which batches deemed at risk by Autoliv had been consumed and the specific vehicle identification numbers of vehicles that may have received parts from these batches. In July, the qualification/identification of damaged parts was confirmed, and the subject matter experts within JLR confirmed the impact of damaged pretentioners on the Supplementary Restraints System (SRS) and on occupant protection. At the PSCC of July 13, 2022, the scope was discussed along with exposure and vehicle disposition confirmed. Based on the feedback provided, the PSCC progressed the issue to the Recall Determination Committee (RDC) for review. The RDC reviewed the issue on July 14, 2022, and concluded that it represented an unreasonable risk to safety and a voluntary safety recall should be conducted to inspect the pretensioner on all vehicles identified to be at risk of receiving a damaged pretensioner, and if a damaged component is identified, the seatbelt assembly should be replaced. Description of Remedy : Description of Remedy Program : Owners will be notified and instructed to take their vehicle to an approved Jaguar Land Rover repairer. The technician will inspect the seat belt pretensioner tube for damage and if damage is identified, the seat belt retractor will be replaced. There will be no charge to the owners for this repair. The affected vehicles will be covered under Jaguar’s new vehicle warranty program. Therefore, reimbursement for pre-notice remedies are not necessary because the affected vehicles are still under warranty. How Remedy Component Differs from Recalled Component : NR Identify How/When Recall Condition was Corrected in Production : NR Part 573 Safety Recall Report 22V-524 Page 8 The information contained in this report was submitted pursuant to 49 CFR §573 Recall Schedule : Description of Recall Schedule : Distribution of owner notification letters will occur on or before September 16, 2022. Notifications to dealers will occur on August 4, 2022. Planned Dealer Notification Date : AUG 04, 2022 – AUG 04, 2022 Planned Owner Notification Date : SEP 16, 2022 – SEP 16, 2022 * NR – Not Reported
**************************************************************************************************************
OMB Control No.: 2127-0004 Part 573 Safety Recall Report 22V-524 The information contained in this report was submitted pursuant to 49 CFR §573 Manufacturer Name : Jaguar Land Rover North America, LLC Submission Date : JUL 21, 2022 NHTSA Recall No. : 22V-524 Manufacturer Recall No. : H412 Manufacturer Information : Manufacturer Name : Jaguar Land Rover North America, LLC Address : 100 Jaguar Land Rover Way Mahwah NJ 07495 Company phone : 8188500 Population : Number of potentially involved : 176 Estimated percentage with defect : 100 % Vehicle Information : Vehicle 1 : 2022-2022 JAGUAR F-TYPE Vehicle Type : LIGHT VEHICLES Body Style : 2-DOOR Power Train : NR Descriptive Information : Jaguar Land Rover are conducting a voluntary safety recall campaign involving certain 2022 Model Year Jaguar F-TYPE vehicles built at the Castle Bromwich & Solihull Vehicle Assembly Plants from 17th January 2022 – 8th March 2022. Approximately 176 vehicles in the United States and Federalized Territories. The basis of the recall population was derived from the production periods seatbelts provided could have been incorrectly manufactured by Autoliv and installed into vehicles. Production Dates : JAN 17, 2022 – MAR 08, 2022 VIN Range 1 : Begin : SAJDD1EE9NCK78757 End : SAJD85EE3NCK79169 Not sequential Vehicle 2 : 2022-2022 JAGUAR F-PACE Vehicle Type : LIGHT VEHICLES Body Style : SUV Power Train : NR Descriptive Information : Jaguar Land Rover are conducting a voluntary safety recall campaign involving certain 2022 Model Year Jaguar F-PACE vehicles built at the Castle Bromwich & Solihull Vehicle Assembly Plants from 17th January 2022 – 8th March 2022. Approximately 176 vehicles in the United States and Federalized Territories. The basis of the recall population was derived from the production periods seatbelts provided could have been incorrectly manufactured by Autoliv and installed into vehicles. Production Dates : JAN 17, 2022 – MAR 08, 2022 VIN Range 1 : Begin : SADCJ2EX2NA693574 End : SADCZ2EE0NA694892 Not sequential Part 573 Safety Recall Report 22V-524 Page 2 The information contained in this report was submitted pursuant to 49 CFR §573 Vehicle 3 : 2022-2022 JAGUAR XF Vehicle Type : LIGHT VEHICLES Body Style : 4-DOOR Power Train : NR Descriptive Information : Jaguar Land Rover are conducting a voluntary safety recall campaign involving certain 2022 Model Year Jaguar XF vehicles built at the Castle Bromwich & Solihull Vehicle Assembly Plants from 17th January 2022 – 8th March 2022. Approximately 176 vehicles in the United States and Federalized Territories. The basis of the recall population was derived from the production periods seatbelts provided could have been incorrectly manufactured by Autoliv and installed into vehicles. Production Dates : JAN 17, 2022 – MAR 08, 2022 VIN Range 1 : Begin : SAJBL4GX1NCY91515 End : SAJBL4GX5NCY91713 Not sequential Description of Defect : Description of the Defect : A concern has been identified on certain 2022 Model Year Jaguar F-TYPE, FPACE & XF vehicles where a damaged front seat belt pretensioner tube may have been installed on the seat belt retractor. FMVSS 1 : NR FMVSS 2 : NR Description of the Safety Risk : A damaged front seat belt pretensioner tube could prevent the pretensioner from correctly operating by not pre-tensioning the seat belt in the event of an accident where it would normally operate. This may result in a reduced level or complete loss of pre-tensioning in the event of a crash and increased occupant injury. Description of the Cause : NR Identification of Any Warning that can Occur : NR Involved Components : Component Name 1 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B08-AC8AAM Part 573 Safety Recall Report 22V-524 Page 3 The information contained in this report was submitted pursuant to 49 CFR §573 Component Name 2 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B09-AC8AAM Component Name 3 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B08-AC8PVJ Component Name 4 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B08-LD8AAM Component Name 5 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B08-LD8PVJ Component Name 6 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B09-AC8PVJ Component Name 7 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B09-ED8AAM Component Name 8 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : CPLA-611B09-ED8PVJ Part 573 Safety Recall Report 22V-524 Page 4 The information contained in this report was submitted pursuant to 49 CFR §573 Component Name 9 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : FK72-611B09-AE8PVJ Component Name 10 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : GX63-611B08-AF8PVJ Component Name 11 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : GX63-611B09-BF8PVJ Component Name 12 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : GX73-611B08-AE8PVJ Component Name 13 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : GX73-611B09-CD8PVJ Component Name 14 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : HK83-611B09-AD8PVJ Component Name 15 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : HK83-611B09-BD8PVJ Part 573 Safety Recall Report 22V-524 Page 5 The information contained in this report was submitted pursuant to 49 CFR §573 Component Name 16 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : HY32-611B08-AD8PVJ Component Name 17 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : HY32-611B08-CD8PVJ Component Name 18 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : HY32-611B09-AD8PVJ Component Name 19 : Seat Belt Assembly Component Description : Seat Belt Assemblyv Component Part Number : HY32-611B09-DA8PVJ Component Name 20 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : JX53-611B08-BB0CJA Component Name 21 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : JX53-611B08-BB0PVJ Component Name 22 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : JX53-611B09-AC0CJA Part 573 Safety Recall Report 22V-524 Page 6 The information contained in this report was submitted pursuant to 49 CFR §573 Component Name 23 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : JX53-611B09-BB0PVJ Component Name 24 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : L8B2-6110B08-AB8PVJ Component Name 25 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : L8B2-6110B08-CB8PVJ Component Name 26 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : L8B2-6110B08-EB8PVJ Component Name 27 : Seat Belt Assembly, Seat Belt Assembly Component Description : Seat Belt Assembly, Seat Belt Assembly Component Part Number : L8B2-6110B09-AB8PVJ, HK83-611B08-AD8PVJ Component Name 28 : Seat Belt Assembly, Seat Belt Assembly Component Description : Seat Belt Assembly, Seat Belt Assembly Component Part Number : L8B2-6110B09-DB8PVJ, L8B2-611B09-BB8PVJ Component Name 29 : Seat Belt Assembly Component Description : Seat Belt Assembly Component Part Number : LK72-611B08-AB8PVJ Part 573 Safety Recall Report 22V-524 Page 7 The information contained in this report was submitted pursuant to 49 CFR §573 Supplier Identification : Component Manufacturer Name : AUTOLIV B.V. & CO. KG Address : NR SOPRONKOVESD Foreign States 9483 Country : Hungary Chronology : Following a notification from Autoliv that a defect had been identified during their manufacturing process that caused damage to a small number of front seat belt pretentioner tubes, Jaguar Land Rover (JLR) opened a PSCC (Product Safety & Compliance Committee) investigation on May 25, 2022. The PSCC requested that Vehicle Assembly Plants conduct an exercise to identify if they had received any parts from the batches Autoliv deemed at risk and the population of affected vehicles that may have received parts from these batches. On June 1, 2022, Autoliv presented the issue to the PSCC, Autoliv explained the issue that had been identified on one of their seatbelt production lines and the potential impact on the component functionality. During June, each vehicle assembly plant conducted detailed research to identify which batches deemed at risk by Autoliv had been consumed and the specific vehicle identification numbers of vehicles that may have received parts from these batches. In July, the qualification/identification of damaged parts was confirmed, and the subject matter experts within JLR confirmed the impact of damaged pretentioners on the Supplementary Restraints System (SRS) and on occupant protection. At the PSCC of July 13, 2022, the scope was discussed along with exposure and vehicle disposition confirmed. Based on the feedback provided, the PSCC progressed the issue to the Recall Determination Committee (RDC) for review. The RDC reviewed the issue on July 14, 2022, and concluded that it represented an unreasonable risk to safety and a voluntary safety recall should be conducted to inspect the pretensioner on all vehicles identified to be at risk of receiving a damaged pretensioner, and if a damaged component is identified, the seatbelt assembly should be replaced. Description of Remedy : Description of Remedy Program : Owners will be notified and instructed to take their vehicle to an approved Jaguar Land Rover repairer. The technician will inspect the seat belt pretensioner tube for damage and if damage is identified, the seat belt retractor will be replaced. There will be no charge to the owners for this repair. The affected vehicles will be covered under Jaguar’s new vehicle warranty program. Therefore, reimbursement for pre-notice remedies are not necessary because the affected vehicles are still under warranty. How Remedy Component Differs from Recalled Component : NR Identify How/When Recall Condition was Corrected in Production : NR Part 573 Safety Recall Report 22V-524 Page 8 The information contained in this report was submitted pursuant to 49 CFR §573 Recall Schedule : Description of Recall Schedule : Distribution of owner notification letters will occur on or before September 16, 2022. Notifications to dealers will occur on August 4, 2022. Planned Dealer Notification Date : AUG 04, 2022 – AUG 04, 2022 Planned Owner Notification Date : SEP 16, 2022 – SEP 16, 2022 * NR – Not Reported
SEOCONTENT-END